Categories

Pololu ACS709 current sensor -75A do +75A*

Current sensor working in the range of +/- 75 A, based on the Hall effect. The output is an analog voltage. Supply voltage is from 3 V to 5.5 V.

More details

PLL-00526

Dodano produkt do koszyka

In stock, shipping 24 hours!

Cena: 37,90 zł

Product description: current sensor ACS709 -75A +75A - module Pololu

The module consists of a printed circuit board made for the system Allegro  ACS709LLFTR-35BB-T. The sensor operates based on the Hall effect. The chip can be powered from a voltage in the range: 3 V to 5.5 V. Pin FAULT is by default in the high status. It reaches a low status when the value of the measured current exceeds the given threshold. The threshold value is selected by indicating the the appropriate voltage on the VOC pin. It depends on the values of the resistors of the voltage divider shown in the diagram below. By default, the threshold is set at 57 A but it can be changed by adding external resistor. Reset the error flag (low status) to FAULT pin through indicating the low status to the FAULT_EN pin (by default, it is pulled up to VCC). More details in the documentation.

Wymiary czujnika prądu ACS709 firmy Allegro   Wymiary modułu czujnik prądu ACS709 +/- 75A

The main characteristics of the current sensor ACS709 -75 to +75

  • The system is optimized for current flowing in both directions from - 37,5 to 37,5 A with a linear measurement range from -75 to 75 A (please, pay attention to the heat limitations below).
  • Due to the low resistance of the system (1.1m Om) and channeling, the power losses are very small.
  • Through the use of Hall effect, the current paths are isolated from the logic part.
  • The bandwidth is up to 120 kHz with the possibility of reduction by adding an additional condenser
  • Precision of 2% at room temperature.
  • Operating temperature: -40 °C to 150 °C.

 

Attention!

Maximum current is measured according to the duration of the measurement. For example, a current of 50 A can flow through the system for maximum, 20 seconds, without causing damage. After this time, the module reaches the temperature to above 150 °C. For the current above 30A, the manufacturer recommends to use the additional cooling.

Pins of the ACS709 current sensor -75 to +75 A

Wyprowadzenia czujnika prądu ACS709 

For proper operation, to the sensor must be connected: the measured current (IP+ and IP-), supply voltage of 3V to 5.5 V (VCC and GND) and output (VIOUT). The remaining pins are not required, they are used to connect the external capacitors as was shown in the figure above.

The output voltage is proportional to the intensity of the measured current. The value is centered to VCC/2. During the power supply of the 5V, the output voltage changes to 28mV on 1A of the measured current. The positive direction of the current, increases the value of the voltage, the negative, on the contrary, decreases it. The pattern on the output voltage VOUT switches as follows:

 

VIOUT = (0.028 V/A * i + 2.5 V) * VCC / 5 V

 

Pin VZCR is the reference value of the voltage for zero current flow (0 A). This value is approximately equal to VCC/2, it allows to accurately calculate the intensity of the measured current.

 

Pin FILT allows you to connect an external capacitor Cf (between FILT and GND) which allows to limit the bandwidth, by default, set to 120kHz. More information about the external filtration, can be found in the system documentation.

Diagram of the module

 

Schemat podłączenia czujnika prądu ACS709

Specification

  • Supply voltage of the logic part: 3.0 V to 5.5 V
  • Current consumption of the logic part: 11 mA
  • Sensitivity for power supply of 3.3 V: 0,018 V/A
  • Module weight: 1.7 g
  • Dimensions: 21 x 23 mm

 

SAME DAY SHIPPING

Posting the payment for the order on our account on a business day up to 13:00 means sending the goods on the same day!

 

The time of payment depends on the hours of ELIXIR session of the sender's bank and the recipient of the transfer (more information on this subject, for example on the websitehttp://www.kiedy-przelew.pl/).

 

The table presents available forms of delivery in Poland

 

Carrier and
regulations

Bank wire
transfer

Payment
by cash

Delivery
time

Poczta Polska

terms of service

9,90 PLN17,90 PLN1-3 days

Kurier GLS

terms of service

14,90 PLN22,90 PLN

1-2 days

Paczkomaty 24/7 

terms of service

12,90 PLN-1-3 days

If the amount to pay for products exceeds 500 PLN
Delivery is for free!

 

  • Free delivery of orders over 500 PLN does not apply to parcels addressed outside of Poland.
  • Free delivery does not apply when changing orders.
  • The delivery period is counted in working days from the date of dispatch of the order.