Arduino - Strona 5
DFRduino Uno v3 - compatible with Arduino
DFRobot module fully compatible with Arduino Uno R3. It has 14 digital inputs/outputs, 6 PWM channels, 6 analog inputs and popular communication interfaces. Colored connectors...DataLogger Shield V1.0 RTC DS1307 with SD card reader - Shield for Arduino - Iduino ST1046
Shield for Arduino with RTC DS1307 and a slot for SD memory cards. It can be used as a data logger, it has a place for a round CR1220 battery and for additional module. It...Grove - Arduino Sensor Kit - set of 10 modules with BaseShield for Arduino - Seeedstudio 103030375
Set consisting of 10 different sensors and modules . The modules are placed on a single board, allowing you to keep order, there is no need for an additional contact board....Beetle CM-32U4 - ATmega32U4 - compatible with Arduino Leonardo - DFRobot DFR0816
An improved version of the Beetle module with the popular ATmega32U4 microcontroller, known from the Arduino Leonardo module, with which the Beetle CM-32U4 is compatible....Ardi Display - IPS 2'' 240x320 px display overlay for Arduino Uno - SB Components SKU27217
Ardi Display is a module from SB Components that significantly expands the possibilities of Arduino- based projects. Equipped with a 2-inch IPS display with a resolution...- New
DFRobot RS485 MAX485ESA - Shield for Arduino
Shield for Arduino, which allows data transfer via RS485 Protocol, which allows you to connect up to 32 devices on one line with the width of up to 1 km with a maximum speed up...DFRobot Beginner KIT for beginners v3.0
Kit of electronic components for people who want to start their adventure with programming of Arduino. Included are i.a. DFRduino Uno board (compatible with Arduino Uno),...Arduino MKR Zero module ABX00012 - SAMD21-with connectors
Module with chip Atmel SAMD21 Cortex-M0+, allowing you to study modules for 32-bit. Has 256 KB Flash memory, 32 KB SRAM, 22 digital inputs/outputs, 12 channels PWM) and 7...CAN-Bus Shield v2.0 - Shield for Arduino
Shield for Arduino supporting the CAN bus. It is equipped with chips MCP2515 and MCP2551. It communicates via the SPI interface. It works with voltage of 5 V.MXChip Microsoft Azure IoT Developer Kit - DFRobot DFR0512
IoT development board based on STM32F412 ARM Cortex M4F. It is equipped with WiFi module, OLED display, audio codec, motion, pressure, temperature, humidity and magnetometer...- Reduced price
- Promotion
Breadboard - 400 holes transparent
Breadboard is used for creating and testing electronic circuits without soldering. Version with 400 cells, the size of 82.5 x 53 mm, with a transparent body. Stripes denoting...Grove - 4-pin screw connection
Module from the Grove series with a 4-pin screw connection of 3.5 mm. It is designed to connect the cables with diameter from 0.2 mm to 0.8 mm for the microcontroller. It has...Arduino Nano 33 IoT - module ABX00027
Arduino® Nano 33 IoT with connectors is a small board equipped with SAMD21G18A microcontroller and NINA W102 ESP32 module responsible for wireless communication. The board is...Arduino Nano RP2040 Connect with headers - ABX00053
Another module from the Arduino® Nano series, this is the first Arduino® board created in collaboration with the Raspberry Pi. The Arduino® Nano RP2040 Connect module is based...Grove - Button - module with a button
The control module from a Grove series. It has a built-in tact-switch system and pull-down resistor. It communicates with the microcontroller through a digital signal.Digispark kickstarter - ATtiny85 - 5V
Miniature module with ATtiny85 microcontroller, equipped with 8 kb Flash memory and 6 I/O ports. The board was printed with a USB connector, thanks to which the chip can be...The Dreamer Nano v4.0 - compatible with Arduino
DFRobot module compatible with Arduino Leonardo. It has 20 digital inputs/outputs, 7 PWM channels, 12 analogue inputs and popular communication interfaces. The board is...Grove - 10kΩ linear rotary potentiometer - top connector
Potentiometer 10 kOhm with linear rotary. It as a 300° range of rotation. It h as a 4-pin Grove connector on the side of the handle.DFRobot Gravity: Analog 20A Current Sensor
Current sensor operating in the range up to 20 A and up to 311 Volts on the basis of the Hall effect. The output is an analog voltage. The supply voltage is 5 V.Electronic components set for Arduino - Iduino KTS042
A set of prototype parts that you can use to create circuits with Arduino. The set includes: contact board, wire sets, Tact Switch buttons, LEDs, and a table to help identify...Gravity - segment display 4-digital I2C - red - DFRobot DFR0645-R
4-digit, 8-segment Gravity series display , allows you to adjust the brightness of the displayed characters, thanks to 8-stage adjustment, The device has an I2C port...