RGB LED WS2811 8mm addressing - 10pcs

Index: LED-07294 EAN: 5903351244268

LED RGB 5 mm WS2811 with integrated control unit allows you to control the device via the 1-wire bus.

RGB LED WS2811 8mm addressing - 10pcs
€5.90
€4.80 tax excl.
Available
Shipping in 24 hours
PayPal payment

Volume discounts

Quantity Discount You Save
5 5% Up to €1.48
10 10% Up to €5.90
WS2811 LEDs 10 pcs. - diameter:
Manufacturer: OEM

Specification

  • Supply voltage: 5 V
  • Supply current If: 50 mA
  • Lens diameter: 8 mm
  • The choice of colors from 24-bit palette
  • Controlled through digital interface 1-wire with the possibility of connecting several devices on one line
  • Has an individual address of the device

 

Items are sold in sets of 10 pieces.

 

Description

Package of ten RGB LEDs, through which you can easily add colorful visuals to your project. The LED includes a built-in controller that allows you to control with one line connected to a microcontroller, e.g.Arduino,STM32orRaspberry Pi. Because each LED has an individual address, on the same bus you can connect several elements.

 

The product is compatible with Arduino

The company Pololu providesa libraryfor users of the Arduino platform. Online you can find libraries AdafruitNeoPixelandNeoMatrix.

 

Connection

The LED has four pins, as shown in the photo below. When the connection is enabled, by default it lights up in blue color.

 

 

Pin Description
5V The supply voltage of 5 V.
GND The ground of the system.
DIN The control input that must be connected to the controller, or prior LEDs in the chain.
DOUT Additional output for connection of another LED.

 

Below are a few tips that can help to protect your diode from destruction:

  • Never connect voltage higher than 5 V.
  • Connecta capacitorwith capacity not less than 10 UF between the power pins.
  • Avoid changes in work if the power is turned on.
  • Use as short as possible wires on the line of control between the LEDs and the microcontroller.
  • Consider the use of a resistor in the range of 100 Ohms to 1000 Ohms on data lines between mikrokontelerem and diode, in order to reduce noise and prevent accidental powering LEDs with the contact of the processor.

 

Attention!

LEDs can explode, if the voltage exceeds the permissible value. From the tests it follows that the supply voltage of 6 Volts can cause permanent destruction of the diode.

 

Communication Protocol

LEDsWS2811 is controlled with easy, fast communication Protocol. The default state of the bus 0 (low). For setting the color, you pass a series of pulses, where each state that high is one bit: a short pulse (0.35 MS) - the zero, long (0.9 MS) - the logical unit. The interval between successive rising slopes shall be 1.25 µs. After submitting the sequence, the line is held low for 50 µs.

 

 

The color is transferred in three digit RGB (red-green-blue). The brightness of each color is encoded in a series that are transferred 8-bits where the most significant is transmitted first. This means that in order to encode the full color should be converted to 24 bits. The first sequence applies to the LEDs located closest to the controller, and the other second in the chain etc.

 

The used Protocol provides a fast update of the provisions of a number of LEDs in the chain. Developed by PololuArduino library that allows you to change the state of the 30 LEDs in line of 1.1 MS. After the installation of the corresponding color, each LED can hold up to the moment of sending a new sequence, or until power is turned off.

 

Video

 

Nominal power 0.05
LED - type WS2812B
LED lens mat
LED wavelength RGB
Package width 6 cm
Package height 7 cm
Package depth 1 cm
Package weight 0.009 kg

Be the first to ask a question about this product!

Product reviews

RGB LED WS2811 8mm addressing - 10pcs

5/5

Average grade

3

Customers opinion
The following opinions are collected
and verified by
an external partner Trustmate
and come from the post-purchase process.
Włodzimierz J. 09.04.2022 Confirmed purchase Translated review
They work well. You can get interesting lighting effects.
ZOFIA S. 27.03.2022 Confirmed purchase Translated review
All OK
Piotr S. 15.12.2021 Confirmed purchase Translated review
It works perfectly. A great option to start playing with addressable LEDs inexpensively!

Customers who bought this product also bought:

Products from the same category: