• EOL

Moduł 3G/GSM - u-GSM shield v2.19 UG95E - for Arduino and Raspberry Pi - SMA connector

Index: ITB-14629 EAN: 5904422322397

The module allows for communication in 3G / GSM standard. It allows for voice calls, sending SMS messages. On the board there are: SIM card connector, charging module for Li-Pol / Li-Ion batteries and RESET button. It cooperates with Arduino, Raspberry Pi and BeagleBone, has SMA antenna connector.

Moduł 3G/GSM - u-GSM shield v2.19 UG95E - for Arduino and Raspberry Pi - SMA connector
€67.90
€55.20 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Itbrain Power
Compatibility: Arduino Raspberry Pi

Attention!

The product has been discontinued. Check other products in category.

Product description: 3G/GSM module - u-GSM shield v2.19 UG95E - SMA connector

Module cooperating with Arduino, Raspberry Pi 3B+/ 3B / 2B and Zero / Zero W and BeagleBoneBlack, whichenablescommunication in 3G / GSM standard. It allows to make voicecalls, sendSMSmessages. The board includes: SIM card connector,Li-Pol / Li-Ion batterychargingmoduleandRESETbutton. It has aSMAantenna connectorfor GSM.

Moduł 3G/GSM - u-GSM UG95E

The distribution of components on the u-GSM shield.

Detailed description of the module can be found in the user guide in parts one andtwoand on the manufacturer'swebsite.

3G/GSM module outputs - u-GSM shield

Moduł GSM LTE GPRS NB IoT GNSS

PinDescription
STS
Status quiz.
RI Ring Indicator output.
GND The weight of the system.
VCC 4 V input/output, connected to Li-Pol + pad.
VIN 5V input for Li-Pol charger.
VUSB Output 5 V.
ENA Pin activating, activated by high state.
RST Reset, activated high state.
TX Communication via serial interface.
RX Communication via serial interface.

Connection of 3G/GSM module to Arduino

The system works with ArduinoUnousing the following leads:

PinArduinoDescription
GSM RX D3 Communication via serial interface.
GSM TX D2 Communication via serial interface.
RESET D6 GSM chip reset.
Ena D7 Control of the GSM power supply voltage (On/Off).
VIN (5 V LiPol) 5 V

5 V power supply. Details of connection for LiPol batteries are available in themanufacturer'smanual.

GND

GND The weight of the system.

STATUS

D5 Status quiz.

3G/GSM module connection with RaspberryPi

The module has special breakaway connectors for direct connection to GPIO Raspberry Pi or BeagleBone Black connectors.

In order to start the module with Raspberry Pi the following connections must be made:

PinRPiDescription
GSM RX 10

Communication via serial interface, (not connected for USB communication).

GSM TX 08

Communication via serial interface, (not connected for USB communication).

RESET 18 GSM chip reset.
ON / OFF 16 Control of the GSM power supply voltage (On/Off).
VIN (5 V LiPol) 02/04 Supply voltage 5 V.

GND

04/14 The weight of the system.
STATUS 12 Status quiz.

3G/GSM module specification - uGSM shield

  • Controller: Quectel UG95E
  • Supported standards: 3G / GSM / UMTS / HSPA
  • Frequencies:
    • UMTS: 900 / 2100 MHz
    • GSM: 900 / 1800 MHz
  • Speed:
    • HSUPA / HSPDA: up to 5.76 Mb/s / 7.2 Mb/s
    • UMTS: up to 384 Kb/s (DL)
    • EDGE/GPRS: up to max. 296 Kb/s (DL), max. 236.8 Kb/s (UL) / max. 107 Kb/s (DL), max. 85.6 Kb/s (UL)
  • Nano SIM / micro SIM connector
  • SMA antenna connector
  • Built-in USB-UART converter (USB connector can be used to power the module)
  • Automatic selection of logical levels from 3 V to 5 V
  • Reset button
  • Works with Arduino, Raspberry Pi 3B+/ 3B / 2B / Zero / Zero W and BeagleBoneBlack withsamplemanufacturer codes
  • Two mounting holes with diameter: 2.5 mm
  • Dimensions of the plate: 45 x 27 mm

Package width 6.5 cm
Package height 6 cm
Package depth 0.5 cm
Package weight 0.011 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: