- EOL
|
Attention! The product has been discontinued. Check other products incategory. |
Product description: SafeHaus SHG-02 natural gas and LPG sensor - 230 V
High quality and sensitive SafeHaus solid-statenatural gas andLPG sensor model SHG-02. It is powered by a 230 V cable. Very easy to install and operate. In case of gas detection it sendsacoustic and opticalalarm signals. The device can operate in temperatures from -10°C to 40°C. The dimensions of the device are117 x 77 x 36 mm. The sensor should be installed in places where there is a risk of gas leakage, e.g.: kitchen, boiler room, bathroom. Remember to install it under the ceiling (about 30 cm from the ceiling) if you want to detect natural gas, and above the floor (about 30 cm above the floor) if you want to detect LPG (propane, butane). You cannot install the sensor in a place where air movement is difficult, e.g. behind furniture.
SafeHaus SHG-02 natural gas and LPG sensor - 230 V.
Advantages of natural gas and LPG sensor
- Optical-acoustic signalling
- Easy to install and operate
- Detects natural gas, propane and butane (LPG)
- It is certified andapproved
- EN50194-1:2009, CE
- BSI Certification Body
- Life span of about 5 years
- Lightweight and compact
The table below shows the operating and notification status of the device.
| Status | Description |
Green POWER LED |
Yellow FAULT diode |
Red ALARM diode |
Beacon audio |
|---|---|---|---|---|---|
|
Auto test |
Power on | It lights up . | It lights up . | It lights up . | 1 beep |
|
Warming up |
Approximately 180 seconds after start-up | Blinks 0.5 s / 1 s | It doesn't shine | It doesn't shine | Excluded |
|
Vigil |
Normal work | Lights steady | It doesn't shine | It doesn't shine | Excluded |
|
Test |
Testing the device after pressing the TEST / HUSH button |
Lights steady | It doesn't shine | Blinks 0.5 s / 1 s | ALARM diode spades |
|
ALARM |
The device detected the gas | Lights steady | It doesn't shine | Blinks 0.5 s / 1 s | ALARM diode spades |
|
Mute |
Press the TEST / HUSH button during the alarm |
Lights steady | It doesn't shine | Blinks 0.5 s / 1 s | Excluded |
|
Sensor malfunction |
Contact the service | Lights steady | Lights steady | It doesn't shine | 1 beep every 30 seconds |
| End of life |
The device should swap for new ones |
Lights steady | Lights steady | It doesn't shine | 3 beep every 30 seconds |
|
No power supply |
The power cord is disconnected | It doesn't shine | It doesn't shine | It doesn't shine | Excluded |
Ifan alarm sounds,be calm anddo the following:
- Switch off all gas appliances
- Open windows and doors to ventilate rooms
- Do not turn on or off any electrical devices, including gas detectors
- Switch off the gas supply by shutting off the main valve in the building
- Do not use the phone in a gas room
- Extinguish all sources of open fire in the building (including cigarettes)
- Contact the gas service or its supplier
|
Attention! Before connecting, please read the supplied manual. After connecting the power supply the sensor needs about 3 minutes for calibration. |
We also offer otheralarmsensors.
Contents of the set:
- SafeHaus SHG-02 natural gas and LPG sensor
- Mounting screws and studs
- Operating instructions
Gas sensor specifications
- Power supply: 230 V AC / 50 to 60 Hz
- Sensor type: solid-state
- Detects: natural gas (methane), LPG, propane, butane (and mixtures thereof)
- Sensitivity: 6% DGW (Lower Explosion Limit)
- Volume: > 85 dB at 1 meter distance
- Energy consumption: < 4 W
- Operating temperature: -10°C to 40°C
- Operating humidity: 0% to 95% RH
- Dimensions: 117 x 77 x 36 mm
- Lifetime: approx. 5 years
- Weight: 66 g
Useful links |
