STSPIN820 Stepper Motor Driver Carrier with headers - Pololu 2879

Index: PLL-13679 EAN: 5904422321154

Stepper motor driver based on the STSPIN820 chip. It is powered from 7 V to 45 V, with maximum current consumption of 0.9 A per coil without heatsink (momentary up to 1.5 A). Maximum resolution: 1/256th step. Supports one bipolar motor. Can be used as replacement for A4988 chip. Version with soldered connectors.

STSPIN820 Stepper Motor Driver Carrier with headers - Pololu 2879
€22.90
€18.62 tax excl.
Waiting time: 4-6 weeks
Only on request
PayPal payment
Manufacturer: Pololu
Compatibility: Arduino Raspberry Pi

Product description: STSPIN820 - 45V / 0,9A stepper motor driver - with connectors - Pololu 2879

The module based on theSTSPIN820driver allows to control a bipolar steppermotorwith the maximum current consumption up to 0,9 A per coil without additional cooling (momentary up to 1,5 A). It is powered from 7 V to 45 V. We recommend that you read theSTSPIN820driverdocumentationbefore use. Below are some of the main features of the product:

  • The module features asimplestep and directioncontrol interface
  • Has theability to operate in 8 modes: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, 1/32-step, 1/128-step and 1/256-step
  • Providescontrol of the maximum motor currentvia apotentiometer, allowing you to use a higher than rated supply voltage for the motors, so you can achieve higher step speeds
  • Motors can be poweredfrom 7 V to 45 V
  • Current consumptionup to 0.9 A(1.5 A momentary)
  • Thanks to the integrated voltage regulator, the user does not need to supply additional power to the logic part.
  • STSPIN820works with systems with logic part voltage of both3.3 V and 5 V.
  • It has protectionagainst overcurrent, overtemperature and short-circuit.
  • In order to increase heat dissipation surface the board was made in 4-layer technology with thicker copper cover
  • Exposed ground area on the bottom for soldering the cooling elements
  • The module is compatible, in terms of size and pinout, with the chip based onA4988driver
STSPIN820 - sterownik silnika krokowego 45V / 0,9A

STSPIN820 stepper motor driver 45 V / 0.9 A - with Pololu 2879 connectors.

The module has soldered pins. Aversion withoutpins is also available in our offer.

STSPIN820 - sterownik silnika krokowego 45V / 0,9A

Controller connection

To control a bipolar stepper motor, connect the system according to the drawing below. The driver allows also for working with some unipolar motors, details are in themanual.

MODE0 MODE1 MODE2 Resolution
Low Low Low Full step
High Low Low 1/2 step
Low High Low 1/4 step
High High Low 1/8 step
Low Low High 1/16 step
High Low High 1/32nd step
Low High High 1/128th step
High High High 1/256th step

Controlling

One pulse applied to the STEP pin causes one motor step in the direction selected by applying the appropriate logic state (high or low) to the DIR pinout. STEP and DIR pins are not internally pulled up. Ifthe motoris to spin in one direction only, the DIR pin can be permanently connected to VCC or GND.

The STSPIN820 has two different inputs to control the power status, STBY / RESET and EN / FAULT.

  • when STBY pin is connected to low state, controller enters low power mode and disables controller outputs
  • ENABLE pin by default is pulled to low state enabling the module, it can also disable the outputs.

TheSTSPIN820controllercan detect errors by setting the EN/FAULTpin to low.FAULT is not available by default to maintain compatibility with the A4988 module. It can be obtained by bridging the jumper marked F on the back of the board.

A microstep controller such as the STSPIN820 allows the motor to operate with a high resolution of up to 1/256th of a step. The step size is selected using the MODE1, MODE2 and MODE3 inputs - the available modes are shown in the table below. By default, all three leads are in float mode, so they must be connected to VCC or GND.

Power supply

The chip can be supplied with voltage from 7 V to 45 V connected between VIN (+) and GND (-) pins. The voltage should be filtered by an external capacitor placed as close as possible to the controller board. Its capacity depends on the maximum current drawn by the motor.

Attention!

In certain conditions, even a relatively low supply voltage can cause spikes (voltage spikes) with a high amplitude, exceeding the permissible value of 45 V. Such a situation leads to permanent damage to the system. One way to avoid this problem is to place a capacitor (at least 47uF), as close as possible to the VIN and GND pins of the controller module.

Connecting and disconnecting the motor while the controller is on can damage the system.

STSPIN820 - sterownik silnika krokowego 45V / 0,9A - ze złączami - Pololu 2879

STSPIN820 - 45V / 0,9A stepper motor driver - with connectors.

Current limitation

To maintain a high switching speed of the steps, a higher motor supply voltage than the nominal one can be used. You just need to limit the maximum current flowing through the coils to the motor catalog value.

The module allows you to actively limit the current using a potentiometer. One way of limiting is to set the controller to full step mode and measure the current flowing through one coil without providing a signal to the STEP input. The measured current is 100% of the set limit (both coils are always on and limited to 100% in full step mode).

Another way is to measure the voltage on the VREF pin (marked with a circle on the PCB) and calculate the current limit). The current limit can be calculated from the formula:

Current Limit = VREF ×5

Schematic diagram

The circuit contains the necessary passive components for proper operation ofthe controller. The circuit diagram is shown in the figure below.

STSPIN820 - sterownik silnika krokowego 45V / 0,9A

Controller's diagram.

STSPIN820 - sterownik silnika krokowego 45V / 0,9A - ze złączami - Pololu 2879

Controller dimensions.

Stepper motor driver specification

  • Driver: STSPPIN820
  • Supply voltage: 7 V to 45 V
  • Continuous current per coil: 0,9 A
  • Maximum instantaneous current per coil: 1,5 A
  • Supply voltage for logic part: 2 V to 5.5 V
  • Resolution: 1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/128 and 1/256 steps
  • Current limitation: built-in potentiometer
  • Reverse polarity protection: none
  • Soldered pins: yes
  • Module dimensions: 20 x 15 mm
  • Weight: 1.4 g
Voltage to 7.0 V
Voltage from 45 V
Current 0.8 A
Channels 1
Package width 9 cm
Package height 2 cm
Package depth 8 cm
Package weight 0.006 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: