Categories

Soldering station 2in1 hotair and tip-based WEP 878D - 700W_

Soldering station 2in1 using soldering tips and hotair, with a total capacity of 700 watts. The device has an adjustable temperature, standby mode and LED display. It also memorizes the last set temperature.

More details

LUT-00907

WEP

Dodano produkt do koszyka

In stock, shipping 24 hours!

Price 192,00 zł

Description

WEP 878D soldering iron has an LED display which shows the temperature of hot air. Temperature control of air blow is performed with buttons, and the blow power adjustment with the larger of the two knobs. The temperature of the soldering iron is set with the smaller knob.

 

The station has a sensor in the base of the iron, with which, after putting down the iron, the device cools a heating element from 3 to 8 minutes, then it turns off (switches to standby state). This procedure allows you to save energy, increase service life, and, above all, ensures greater safety. After reaching the standby mode, the station can be completely switched off with the button or  activated by holding up the iron.

 

The station is used in the electronic repair services for safe soldering of QFP, BGA, SMD,PLCC, and other temperature-sensitive elements.

 

Check out our offer of additional tips!

Specification
  • Supply voltage: 230 V / 50 Hz (network)
  • Power: 700 W
  • The station is controlled by the microcontroller which ensures a high stability
  • The device has a standby mode
  • Remembers the set temperature
  • The station has an ergonomical body

 

Hotair soldering iron

  • Adjustable temperature of hot air from 100 °C to 480 °C
  • Temperature stability: +/- 1 °C
  • LED display
  • Temperature setting buttons
  • Smooth regulation of air flow by means of buttons
  • Air consumption: max. up to 120 litres/minute
  • The hot air head size 22mm (fits all nozzles from the stations PT / Aoyue)

 

Soldering iron with tips

  • Adjustable temperature soldering tip: 200 °C to 480 °C
  • Temperature stability: +/- 2 °C
  • Soldering iron power: 60 W
 

Includes:

  • Soldering station WEP 878D
  • Hotair iron holder
  • Set of nozzles:
    • round nozzle with a diameter of 7 mm
    • round nozzle with a diameter of 9 mm
    • square nozzle 12x12 mm
  • Soldering iron holder with a cleaning sponge
  • Soldering iron 907A with the T-I tip
  • Gripper for lifting circuits

 

First run

  • You should not run the device immediately after delivery.
  • Equipment must remain for about 12 hours at room temperature before switching on.
  • All complaints caused by running of the equipment too soon will be denied.
  • You must completely remove the screw/screws from the bottom station if the source of air supply is the compressor. These screws are marked in red (1 or 3 screws depending on model).

 

Note

Heating elements (heaters) and the tips are not subject to warranty, and you must purchase new ones.

Our range of accessories for soldering:
  • Voltage to 220 V AC
  • Voltage from 240 V AC
  • Voltage nominal 230 V AC
  • Nominal power 700 W
  • Temperature 200 - 480 °C
  • Solder - Fan no
  • Solder - real temperature reading: yes
  • Solder - Hotair: yes
  • Solder - Type A/C: digital

SAME DAY SHIPPING

Posting the payment for the order on our account on a business day up to 13:00 means sending the goods on the same day!

 

The time of payment depends on the hours of ELIXIR session of the sender's bank and the recipient of the transfer (more information on this subject, for example on the websitehttp://www.kiedy-przelew.pl/).

 

The table presents available forms of delivery in Poland

 

Carrier and
regulations

Bank wire
transfer

Payment
by cash

Delivery
time

Poczta Polska

terms of service

9,90 PLN17,90 PLN1-3 days

Kurier GLS

terms of service

14,90 PLN22,90 PLN

1-2 days

Paczkomaty 24/7 

terms of service

12,90 PLN-1-3 days

If the amount to pay for products exceeds 500 PLN
Delivery is for free!

 

  • Free delivery of orders over 500 PLN does not apply to parcels addressed outside of Poland.
  • Free delivery does not apply when changing orders.
  • The delivery period is counted in working days from the date of dispatch of the order.