Soldering station hotair WEP 858D with fan in iron - 650W

Index: LUT-02768 EAN: 5907558240184

650 W hotair soldering iron with LED display. The device has a compact casing that takes up little space. The station has adjustable temperature from 100 °C to 500 °C and blowing power.

Soldering station hotair WEP 858D with fan in iron - 650W
€33.90
€27.56 tax excl.
Available
Shipping in 24 hours
PayPal payment
Manufacturer: WEP

Description:WEP 858D hotair soldering station with fan in flask - 650W

650 W hotair soldering iron with LED display. The device has a compact casing that takes up little space. The station has adjustable temperature and blowing power.

Specification of WEP 858D hotair soldering station with fan.

  • Power supply voltage: 230 V / 50 Hz (mains)
  • Power: 650 W
  • Digital temperature control from 100 °C to 500 °C
  • Air outlet control up to 120 l/min at knob output
  • The fan is driven by a brushless motor
  • The device has a standby mode, automatically activated when the flask is placed on the stand
  • The station has a compact housing
  • Reading the set flow rate is possible via the LED display

Included with WEP 858D soldering station:

  • Soldering station WEP 858D
  • Hotair flask tray
  • A set of nozzles:
    • round nozzle with 7 mm diameter
    • round nozzle with a diameter of 9 mm
    • square 11 x 11 mm
  • System lift gripper

First start-up

  • Do not start it up immediately after the equipment is delivered.
  • The equipment should remain at room temperature for approximately 12 hours before start-up.
  • Any reports of faults caused by premature start-up will be rejected.
  • Completely remove the screw(s) from the bottom of the station if the source of airflow is a compressor. These screws are marked in red (1 or 3 screws depending on model).

We also offer soldering accessories:

The perfect tool for surface mounting of electronic components

One of the conditions for proper operation of electronic devices according to the design is the correct assembly of their components. Most often, in the construction of devices, we can find elements such as threaded assembly (THT) and surface assembly (SMD). For surface mounting, especially integrated circuits with a more dense grid of outputs than 2.54 mm (as is the case with most integrated circuits in DIP and SIP enclosures), the WEP 858D hot air soldering station is perfect. Digital temperature display and stepless adjustment of the air stream allow for proper selection of the station's power during installation and service of the electronics.

Hot air - not only soldering

The WEP 858D soldering station is equipped with a soldering flask with built-in heater and fan. The flask is very light, which translates into comfort of work. Thanks to the wide temperature range and three different nozzles included in the set, the 858D station can be used not only for soldering, but also for shrinking heat-shrink tubes, joining hot plastic elements and removing old paint from metal surfaces. The hallotron sensor built into the flask automatically switches the station into standby mode when the flask is placed on a tripod. Similarly, after lifting the flask from the tripod, the control system starts the fan in the flask and heats the heater to the previously set temperature.

Voltage to 220 V AC
Voltage from 240 V AC
Voltage nominal 230 V AC
Nominal power 700 W
Temperature 100 - 480 °C
Solder - Fan yes
Solder - Hotair yes
Solder - Type A/C digital
Package width 26 cm
Package height 16 cm
Package depth 15 cm
Package weight 1.75 kg

Be the first to ask a question about this product!

Product reviews

Soldering station hotair WEP 858D with fan in iron - 650W

5/5

Average grade

6

Customers opinion
The following opinions are collected
and verified by
an external partner Trustmate
and come from the post-purchase process.

Zdjęcia użytkowników

Customers who bought this product also bought:

Products from the same category: