Soldering station Yihua 898BD hotair with fan - 700W*

Soldering iron grotowa (50 W) and hot air (hotair) in one. The total capacity of the station is 700 W. The device has an adjustable temperature and two LED displays. The venting is provided through a fan located in the flask.

More details

More info
Data sheet
Delivery

Description

Station WEP 898BD has two LED displays, which can read the temperature of hot air and flask soldering iron. Temperature adjustment is done using buttons, airflow with knob.

The device has sensor in the mount that, when putting off flask, the station cooles the heating element.

Stable and effective airflow is provided through a fan located in the flask. The fan is driven by a brushless motor, which provides a much higher durability and reliability of the device.

Check out our offer of additional tips!

Specification

Supply voltage: 230 V / 50 Hz (network)
Power: 700 W
The control is performed using PID controller
Protection ESD Safe
Automatic cooling of the heating elements after station's shutdown
The station has an ergonomical body

Hotair Soldering Iron

Adjustable temperature of hot air from 100 °C to 480 °C
Temperature stability +/-1 °C
LED display
Temperature setting with buttons
Smoothly adjustable airflow via knob
Airflow up to 120 l/min
The venting is provided through a fan located in the knob

Grotto Soldering Iron

The flask 907A
Regulation of the soldering tip temperature from 200 °C to 480 °C
Capacity: 50 W
Temperature stability: +/- 2 °C
The potential between tip and ground: up to 2 mV
The resistance between tip and ground: 2 Ohm

Includes:

Station Yihua 898BBD
Stand for the flask hotair
Set of nozzles:

round with a diameter of 6 mm
round with a diameter of 9 mm
square 12x12 mm

Stand for the grotto flask along with a cleaning sponge
The grotto flask 907 A with a tip T-I
A gripper for lifting chips

First run

After delivery of equipment, it should not be immediately started.
Equipment must remain about 12 hours at room temperature before switching on.
All applications for damages caused by the premature commissioning of the equipment, will be denied.
You must completely remove the screw/screws from the bottom of the station if the source of an air supply is compressor. These screws are marked in red (1 or 3 screws depending on model).

Note

Heating elements (heaters) and the tips are not subject to warranty either expressed or implied, and replacing them is chargeable.

Our range of accessories for soldering:

Voltage to 220 V AC
Voltage from 240 V AC
Voltage nominal 230 V AC
Nominal power 700 W
Temperature 200 - 480 °C
Solder - Fan yes
Solder - real temperature reading: yes
Solder - Hotair: yes
Solder - Type A/C: digital

SAME DAY SHIPPING

Posting the payment for the order on our account on a business day up to 13:00 means sending the goods on the same day!

The time of payment depends on the hours of ELIXIR session of the sender's bank and the recipient of the transfer (more information on this subject, for example on the websitehttp://www.kiedy-przelew.pl/).

The table presents available forms of delivery in Poland

Carrier and regulations	Bank wire transfer	Payment by cash	Delivery time
Poczta Polska terms of service	9,90 PLN	17,90 PLN	1-3 days
Kurier GLS terms of service	14,90 PLN	22,90 PLN	1-2 days
Paczkomaty 24/7 terms of service	12,90 PLN	-	1-3 days
If the amount to pay for products exceeds 500 PLN Delivery is for free!

Free delivery of orders over 500 PLN does not apply to parcels addressed outside of Poland.
Free delivery does not apply when changing orders.
The delivery period is counted in working days from the date of dispatch of the order.