Categories

Stepper motor driver A4988 RepRap - green_

Stepper motor driver based on the A4988 system. Voltage supply in the range from 8V to 35 V, with maximum current consumption of 1 A per coil. Maximum resolution: 1/16 of a step.

More details

MOD-02964

Add to cart

This product is no longer in stock


Notify me when available

Price 11,90 zł

Specification:

  • Motor supply voltage: 8 V to 35 V
  • Current: 1 a max. per coil
  • Voltage digital logic supply: 3 V - 5.5 V
  • Simple control interface
  • Work in 5 different modes: full step, 1/2, 1/4, 1/8 and 1/16 step
  • Ability to adjust the current consumed by the motor with a potentiometer
  • Soldered goldpin connectors

 sterownik silnika krokowego A4988 RepRap

The controller Ramps 1.4 module Arduino Mega 2560 and wpiętymi drivers A4988.

 

Description

Designed for 3D printers chip driver A4988 allows you to control a stepper motor with active limitation of the maximum current.

 

Despite the fact that the quality of performance of print and soldermask is not high, the controller remains fully operating. In our offer you will also find high quality module A4988 from Pololu company.

 

Connection driver

In order to rotate the motor one step, you must specify the STEP output high (logical unit), another sequence of zeros and ones moves the motor one step, etc. The choice of direction is accomplished by depositing a correct state on the output DIR (e.g. low - momentum clockwise, low - counterclockwise). The driver also has the choice of resolution of the motor operation.

Power supply

To power the logic part of the module, you need the voltage range from 3 V to 5.5 V, which should be brought into contact VDD. The motor supply voltage is in the range from 8 V to 35 V is supplied to pin UMOT.

 

The system can control the motors with a rated voltage lower than the required 8 V. In this case, it is necessary to limit the maximum current through the potentiometer, so as not to exceed the maximum voltage of the motor. For example, for a motor with a resistance of 5 Ohms on the coil and a current consumption of 1 A, the nominal supply voltage of 5 V. Power voltage of 12 V to limit the current, so it does not exceed 1 A.

 

Attention!

The connection and disconnection of the motor while the driver is turned on can damage the system.

 

Resolution

The step size is selected via the inputs MS1MS2MS3. Possible settings are shown in the table below. Inputs MS1, MS2 and MS3 have internal resistor pull-down (100 kω).

 

MS1MS2MS3Resolution
lowlowlowFull step
highlowlow1/2 step
lowhighlow1/4 step
highhighlow1/8 step
highhighhigh1/16 step

 

 

One pulse on the specified pin STEP causes one step of the motor in the direction selected by making the appropriate logic state on the output DIR. Outputs STEP and DIR are not internally pulled up. If the motor should only rotate in one direction the DIR pin can be permanently connected to VCC or GND.

 

The system has three inputs for monitoring power consumption: SLP EN RESET and their description is in documentation. Please note that the pin RESET to nothing pulled. If not used, you can connect it to the surrounding contact SLEEP.

 

Current limit

The system can control the motors with a rated voltage lower than the required 8 V. In this case, it is necessary to limit the maximum current through the potentiometer, so as not to exceed the maximum voltage of the motor. For example, for a motor with a resistance of 5 Ohms on the coil and a current consumption of 1 A, the nominal supply voltage of 5 V. Power voltage of 12 V to limit the current, so it does not exceed 1 A.

 

Heat

The board was designed so that it can conduct heat when the current consumption is about 1A per coil. If the current is much higher, use an external heatsink to which the assembly can use thermoconductive glue.

 

    SAME DAY SHIPPING

    Posting the payment for the order on our account on a business day up to 13:00 means sending the goods on the same day!

     

    The time of payment depends on the hours of ELIXIR session of the sender's bank and the recipient of the transfer (more information on this subject, for example on the websitehttp://www.kiedy-przelew.pl/).

     

    The table presents available forms of delivery in Poland

     

    Carrier and
    regulations

    Bank wire
    transfer

    Payment
    by cash

    Delivery
    time

    Poczta Polska

    terms of service

    9,90 PLN17,90 PLN1-3 days

    Kurier GLS

    terms of service

    14,90 PLN22,90 PLN

    1-2 days

    Paczkomaty 24/7 

    terms of service

    12,90 PLN-1-3 days

    If the amount to pay for products exceeds 500 PLN
    Delivery is for free!

     

    • Free delivery of orders over 500 PLN does not apply to parcels addressed outside of Poland.
    • Free delivery does not apply when changing orders.
    • The delivery period is counted in working days from the date of dispatch of the order.

    10 other products in the same category: