MAX14870 - dual-channel motor driver 28V/1,7A - extension for Raspberry Pi 4/3+/3/2/B+ - Pololu 3758

Index: PLL-11845 EAN: 5904422318093

Module with dual-channel driver of motors MAX14870 working with voltages from 4.5 V to 36 V and current up to 1.7 A per channel (max 2.5 A). The system can be connected directly with connectors GPIO of minicomputer Raspberry Pi B+, A+, 2, 3, 3+ and 4. The module for self-assembly.

MAX14870 - dual-channel motor driver 28V/1,7A - extension for Raspberry Pi 4/3+/3/2/B+ - Pololu 3758
€21.90
€17.80 tax excl.
Waiting time: 4-6 weeks
Only on request
PayPal payment
Manufacturer: Pololu
Compatibility: Raspberry Pi

Specification

  • Supply voltage: 4.5 V to 36 V
  • Continuous output current per channel: 1.7 A
  • The maximum short-term current per channel: 2.5 A
  • PWM frequency: up to 50 kHz
  • Protection against incorrect attachment of power supply
  • Designed for connectors of the Raspberry Pi
  • The possibility to power Raspberry using additional controller (not included)
  • A Python libraryto facilitate module maintenance
  • Dimensions: 43 x 16 mm
  • Weight: 3.2 g (without connectors)

 

The kit includes: module, screw connectors, goldpin strip for self-assembly.

In our offer you will find alsoassembled, ready to operate system.

 

Description

The module is based on two modules of MAX14870and lets you control the motors with a supply voltage up to 36 V and a continuous current consumption of up to 1,7 A. The driver withstands seconds of jumping current up to 2,5 A. The speed of rotation can be controlled by the control signal of PWM.

Pololu MAX14870

In combination with the Raspberry Pi, using a specially prepared libraries, you can easily control the speed and direction of rotation of two DC motors. Form and pins of the board allow for direct connection to minicomputer, as shown in the pictures above. The system uses a 40-pin GPIO connector.

 

The product is compatible with Raspberry Pi B+

The manufacturer provides a library of Python for users of the Raspberry Pi.

Pololu MAX14870

Modes of operation

The power of the motors was separated from the Raspberry Pi B+. The voltage from the range of 4,5 V to 28 V should be connected to VIN and GND pins. Power of the logic part 3.3 V is consumed from minicomputer.

 

Pololu MAX14870

 

Connection

The following table shows which pins of the Raspberry Pi are used by motor driver:

 

Pin RPi

GPIO

Pin of

driver

Description
5 EN

By default, in the low state, it indicates the disabled outputs of the motors. To run the driver, you must specify the status of high.

6 FAULT

The error output. By default, in the high state. It indicates excessive current or temperature.

12 Motor 1 PWM

The PWM inputs to control the rotation speed of the motor.

The maximum PWM frequency is 50 kHz.

13 Motor 2 PWM

The PWM inputs to control the rotation speed of the motor.

The maximum PWM frequency is 50 kHz.

22 Motor 1 DIR

Pin to choose the direction of rotation. In the low state, the current flows from output A to B. In high state - from B to A.

25 Motor 2 DIR Pin to choose the direction of rotation. In the low state, the current flows from output A to B. In high state - from B to A.

 

Modes of operation

The table shows the operation modes depending on the inputs:

 

EN DIR PWM MxA MxB Operation mode
0 0 PWM PWM (H/L) L Forward rotation at a certain speed PWM %.
0 1 PWM L PWM (H/L) Back rotation at a certain speed PWM %.
1 x 0 L

L

Braking (outputs connected to ground).
1 x x Z Z Disabled output.

 

Additional limit of current

System MAX14870 has SNS input that can be used as an automatic current limiter. By default, it is connected to GND for both systems. To enable the limit, you must first cut the track between the pins of the resistors 1206. Then, to these pins you should connect the appropriate resistor 1206.

Pololu MAX14870

Power of Raspberry Pi

The device provides power to the minicomputer from the input voltage of module (VIN). To stabilize the voltage required for the Raspberry Pi 5 V, you can solder the converter D24V10F5 in specially prepared holes 5 V (output voltage), GND (ground), VOUT (supply voltage of motor). 
Pololu MAX14870

Voltage to 5.0 V
Voltage from 28.0 V
Current 1.7 A
Package width 9 cm
Package height 7.6 cm
Package depth 7 cm
Package weight 0.012 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: