• EOL

Pololu Step-Down Voltage Regulator D24V6ALV - 2,5-7,5V 0,6A

Index: PLL-00945

A small pulse inverter module. Input voltage 4.5 V to 42 V. Adjustable range output voltage: 2.5 V TO 7.5 V. Maximum output current 600 mA.

Pololu Step-Down Voltage Regulator D24V6ALV - 2,5-7,5V 0,6A
€9.00
€7.32 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Pololu

Attention!

The sale of the product has been completed. Check others in thiscategory.

Specification

  • Input voltage: 4.5 V to 42 V
  • Output voltage adjustable: 2.5 V to 7.5 V
  • Maximum output current: 600 mA
  • 500 kHz switching frequency
  • Built-in protection (breaker) to protect against excessive current consumption and excessive temperature
  • Dimensions: 15.3x 10.2 x 4mm
  • Weight: 1g (without connectors)

Description

The adjustable DC-DC converter has a wide input voltage range from 4.5 V to 42 V. It has an efficiency of 80%. The output voltage is set using a potentiometer. The available range is 2.5 V to 7.5 V.The output voltage must not exceed the input voltage.

Exits

The module has four outputs:

  • VIN- input voltage,
  • GND- mass potential,
  • VOUT- output voltage,
  • SHDN- system shutdown.

If the SHDN pin shows a low state (below 0.3 V), the inverter is switched off and the current consumption does not exceed 20 uA. If the high state (above 2.3 V) appears on the SHDN pin, the system will be activated again. The output can be permanently connected to the VIN or left unconnected if the shutdown mode is not used.

The connectors are properly signed on the board. The output roster is 2.54 mm (popular goldpin connectors). The module can be plugged into a contact board, connectedwith wires or soldered into a dedicated PCB.

Output voltage is determined by means of a potentiometer. Setting the voltage higher than input will not damage the system. However, large oscillations will occur. So it is recommended not to set the voltage higher than the input one.

Output voltage oscillogram. VIN is 5V. VOUT is set above 5V.

Output voltage selection

Turning the potentiometer clockwise will increase the output voltage.

Efficiency and output current

Efficiency is defined as the ratio of output power to input power (Power out)/(Power in). This is a very important parameter in the case of operation with portable power sources (batteries and accumulators), where the time of operation on one charging cycle counts. The efficiency dependence on the input voltage is shown in the graphs below.

The graph showing the relation between the output five and potentiometer position for 4-25V and 2.5-7.5V converters.

Dangerous voltage pulses

When connecting the power supply to the module, dangerous, short, high amplitude eclectic impulses (so-called pins) may appear, which may permanently damage the system. Polol's tests show that for voltages above 20V, the pins may have an amplitude exceeding 42V. In order to protect against this undesirable phenomenon it is recommended to solder a capacitor of at least 33 uF as close as possible to the pins supplying the converter.

Length 15 mm
Width 10 mm
Height 4 mm
Voltage to 4.5 V
Voltage from 42 V
Voltage output from 2.5 V
Output voltage to 7.5 V
Current 0.6 A
Stabilizer - Type2 switching
Stabilizer - Type step-down
Package width 0.001 cm
Package height 0.001 cm
Package depth 0.001 cm
Package weight 0.001 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: