Soldering station WEP 898D+ hotair with fan

Soldering iron grotowa increased heating power (75) and hot air (hotair) in one. The total capacity of the station is 700 watts. The device has an adjustable temperature, state protection, as well as two LED displays. Remembers the set temperature. The venting is provided through a fan located in the handle.

More details


Add to cart

Price 289,00 zł



The sale of the product was completed. Check other devices in this category.


  • Supply voltage: 230 V / 50 Hz (network)
  • Power: 700 To
  • The station is controlled by the microcontroller which ensures a high stability
  • The device has a standby mode
  • Remembers the set temperature
  • The station has a body ergonomically


  • Soldering Iron Hotair:
    • Adjustable temperature hot air from 100 - 480 °C
    • Temperature stability +/-1 °C
    • LED display
    • Temperature setting buttons,
    • Infinitely adjustable air supply with regulator
    • Air flow up to 120 litres/min [max]
    • The head size of the hot air 22 mm
    • The venting is provided through a fan located in the handle


  • Soldering Iron Grotowa
    • Regulation of the soldering tip temperature from 200 - 480 °C
    • Temperature stability +/- 1 °C
    • Soldering iron power kolbowej: 75




Unlike the station 878D WEP, WEP 898D has two LED displays, which can read the temperature for hot air and soldering iron kolbowej. Temperature adjustment is done using buttons, fan with regulator.


The device has a sensor in the base that, when placed in a flask, the station must pass through the heating element during the time from 3 to 8 minutes, then the device enters a low energy consumption (the so-called waking state) . Thanks to this we save energy, wydłużamy the service life of the heater and raise the safety. Station remembers the set temperature.


Stable and effective venting is provided through a fan located in the handle. The fan is driven by a brushless motor, which provides a much higher durability and reliability of the device.



  • Station WEP 898D+
  • Stand the flask hotair
  • Set nozzle:
    • round with a diameter of 7 mm
    • a round diameter of 9 mm
    • square 12x12 mm
  • Stand the flask grotową along with a cleaning sponge
  • The bulb grotowa with T slot And
  • A gripper for lifting layouts


First run

  • After delivery of equipment should not immediately start.
  • Equipment must remain about 12 hours at room temperature before switching on.
  • All applications for damages caused by the premature commissioning of the equipment will be denied.
  • You must completely remove the screw/screws from the bottom station if the source of air supply. compressor. These screws are marked in red (1 or 3 screws depending on model).



Our range also accessories for soldering:



Posting the payment for the order on our account on a business day up to 13:00 means sending the goods on the same day!


The time of payment depends on the hours of ELIXIR session of the sender's bank and the recipient of the transfer (more information on this subject, for example on the website


The table presents available forms of delivery in Poland


Carrier and

Bank wire

by cash


Poczta Polska

terms of service

9,90 PLN17,90 PLN1-3 days

Kurier GLS

terms of service

14,90 PLN22,90 PLN

1-2 days

Paczkomaty 24/7 

terms of service

12,90 PLN-1-3 days

If the amount to pay for products exceeds 500 PLN
Delivery is for free!


  • Free delivery of orders over 500 PLN does not apply to parcels addressed outside of Poland.
  • Free delivery does not apply when changing orders.
  • The delivery period is counted in working days from the date of dispatch of the order.