The module is containing the MEMS LPS331AP pressure sensor from ST. On the Board are also required passive elements and a voltage regulator low-dropout, which enables sensor work with systems of 3.3 V and 5 V.
LPS331AP system (documentation) has a built-in temperature compensation and a lot of customizable options, including: selectable resolutions, as well as two programmable external interrupts. The sensors works in the range of 26 kPa to 126 kPa with an accuracy of 0.2 kPa. In the highest resolution mode, noises are at a level of 0.002 kPa. The communication interface is I2C or SPI bus.
The product is compatible with Arduino
The sensor has nine pins for mounting goldpin connectors - 2.54 mm pitch (included). On request, we can solder the strap.
The power is in the range of 2.5 V to 5V, which has to be connected to VIN and GND pins. In the case of using the system powered with the voltage of 3.3 V, VIN pin can be left disconnected, and the power has to be brought directly into the system via pin VDD.
The system communicates via digital I2C or SPI interface. Voltage of the logic signals on the bus must have the same value as the voltage supplied to VIN. In the case of using I2C buss, pins SCL and SDA must be connected. SPI requires the connection of 4 pins: SDI, SDO, CS and SPC.
|The data line of the I2C bus, the line of the input SPI data (SDO in mode 3-wire). High status is equal to the voltage VIN, low GND.|
|Clock line of the I2C bus. High status is equal to the voltage VIN, low, GND.|
|The line of output data of SPI bus (data-out) or change of address in case of I2C. High status is equal to VDD, low GND. (without voltage Converter).|
|CS||Chip select - SPI Enable. Pin is by default in high status (active interface I2C), to begin the SPI communication, you must specify the low status.|
|INT2||Programmable interrupts - high status is equal to the high voltage VDD, low GND. (without voltage Converter).|
|INT1||Programmable interrupt - high status is equal to the high voltage VDD, low GND. (without voltage Converter).|
|VIN||Supply voltage from 2.5 V to 5.5 V|
|VDD||In the case, where the supply voltage is higher than 3.3 V, the output can be used as the voltage output of 3.3 V with maximum current of up to 150mA.|
|GND||The potential of the ground of the system|
By default, the system uses the I2C interface - the CS output is in high state (pulled up, using a resistor to VDD). Details about the I2C communication, can be found in the documentation and in cataloge note from NXP, about the specification of I2C bus.
The sensor has a 7-bit address, whose latest bit is determined with the help of the status on pin SA0. The pin is pulled up to VDD through a 4.7 kΩ resistor, what determines the address to a value of 1011101b.
The bus operates correctly with a frequency of 400 MHz (fast mode), higher values may work correctly but have not been tested.
To choose the connection via the SPI, at pin CS, specified should be the low status (connected to ground). The details of the transfer and a description of the registers is in the documentation of the system.
All the necessary information about communication and service of the module, are in the documentation. Below are several basic facts:
The system is small in size, its contour has is a rectangle with the size of: 22,86 x 10,16 mm. For mounting, used is the hole with inside diameter of 2.18 mm.
The system includes: a voltage regulator, filtering capacitors, pulling up resistors (e.g. I2C bus' lines) and other passive components to facilitate maintenance of the sensor.
STM32F407G-DISC1 - Discovery - STM32F4DISCOVERY* - 105,00 zł
STM32F3 - Discovery - STM32F3DISCOVERY_ - 99,00 zł
Arduino Uno Rev3 - module A000066* - 92,00 zł
Arduino Mega 2560 Rev3 - module A000067* - 159,00 zł
SAME DAY SHIPPING
Posting the payment for the order on our account on a business day up to 13:00 means sending the goods on the same day!
The time of payment depends on the hours of ELIXIR session of the sender's bank and the recipient of the transfer (more information on this subject, for example on the websitehttp://www.kiedy-przelew.pl/).
The table presents available forms of delivery in Poland
|9,90 PLN||17,90 PLN||1-3 days|
|14,90 PLN||22,90 PLN|
|12,90 PLN||-||1-3 days|
If the amount to pay for products exceeds 500 PLN