Categories

Soldering station WEP 862BD+ hotair

WEP 852D+SE is a high-class station rework 2 in 1. Has the hot air and the flask lutowniczą grotową. Applied microcontroller provides precise control of the parameters: temperature, power, airflow and time of operation. System ESD Safe provides security for the solder joint elements.

More details

LUT-01125

Add to cart

Price 329,00 zł

 

Attention!

The sale of the product was completed. Check other devices in this category.

 

 

Specification

  • Voltage: 220V-240V
  • Power consumption: 720W
  • LED displays
  • Microprocessor controlled parameters: temperature, fan power, working time
  • The system is ESD safe

 

  • Soldering Iron Hotair:

    • Infinitely adjustable temperature range: 100 to 480°C
    • Temperature stability: +/-1єс
    • LED display temperature hot trust
    • Air flow: up to 120 l/min
    • Air flow: fan
    • Mode of operation: Automatic / Manual
    • Protection from too high temperature
  • Soldering iron grotowa:

    • Temperature range: 200-480V°C
    • Temperature stability: +/-1єс
    • Sleep mode
    • The potential relative to the grounding below 2mV for
    • The resistance to ground below for 2ohm

Description

WEP 852D+SE is a 2 in 1: blowing hot air and soldering station grotowa power of 60 watts. LED displays inform about the set temperature. The system is ESD Safe and protects the soldered items from damage.

 

Inflating hotair has a ceramic heating element that quickly and evenly heats up. The heater is made of hard alloy, allowing for a long period of time without being subjected to deformations. This increases the stability and prolongs the service life.

In holder for a flask of hot air is micro-sensor. During operation in automatic mode, when you install the bulb, it causes the transition to the idle state, the cooling of the heating element. Then shut off the air fan.

 

Rework station WEP 862BD+ soldering and to rozlutowywania of electronic components, such as: SOIC, CHIP, QFP, PLCC, BGA, SMD (for example, elements in mobile phones).

 

Includes:

  • Rework station WEP 862BD+
  • Stand the flask hotair
  • Set nozzle:
    • round nozzle with a diameter of 4.4 mm 1130
    • round nozzle with a diameter of 8 mm 1195
    • round nozzle with a diameter of 9 mm 1197
    • the nozzle is square 12x12 mm 1313
  • Stand the flask grotową along with a cleaning sponge
  • The bulb grotowa with T slot And
  • A gripper for lifting layouts
  • Power cable

 

First run

  • After delivery of equipment should not immediately start.
  • Equipment must remain about 12 hours at room temperature before switching on.
  • All applications for damages caused by the premature commissioning of the equipment will be denied.
  • You must completely remove the screw/screws from the bottom station if the source of air supply. compressor. These screws are marked in red (1 or 3 screws depending on model).
 

Our range of accessories for soldering:

 

SAME DAY SHIPPING

Posting the payment for the order on our account on a business day up to 13:00 means sending the goods on the same day!

 

The time of payment depends on the hours of ELIXIR session of the sender's bank and the recipient of the transfer (more information on this subject, for example on the websitehttp://www.kiedy-przelew.pl/).

 

The table presents available forms of delivery in Poland

 

Carrier and
regulations

Bank wire
transfer

Payment
by cash

Delivery
time

Poczta Polska

terms of service

9,90 PLN17,90 PLN1-3 days

Kurier GLS

terms of service

14,90 PLN22,90 PLN

1-2 days

Paczkomaty 24/7 

terms of service

12,90 PLN-1-3 days

If the amount to pay for products exceeds 500 PLN
Delivery is for free!

 

  • Free delivery of orders over 500 PLN does not apply to parcels addressed outside of Poland.
  • Free delivery does not apply when changing orders.
  • The delivery period is counted in working days from the date of dispatch of the order.