Categories

NanoPi Fire3 Samsung S5P6818 Octa-Core 1.4GHz + 1GB RAM*

Minicomputer NanoPi, version Fire3 with processor S5P6818 Samsung octa-core ARM Cortex-A53 with a clock frequency of 1.4 GHz. The board has 1GB of DDR3 RAM, a Gigabit Ethernet port, microHDMI connector and USB A slot, 40 GPIOs and a slot for microSD cards. It works with Android and Debian.

More details

NNP-10737

FriendlyARM

Add to cart

Price 179,00 zł

Attention!

The product has been discontinued. Check others products in category.

Description

Minicomputer NanoPi, version Fire3 with processor S5P6818 Samsung octa-core ARM Cortex-A53 with a clock frequency of 1.4 GHz. The board has 1GB of DDR3 RAM, a Gigabit Ethernet port, microHDMI connector and USB A slot, 40 GPIOs and a slot for microSD cards. It works with Android and Debian.

NanoPi Fire3 - Samsung S5P6818 Octa-Core

What it takes to run minicomputer NanoPi?

 

Operating system

NanoPi works with the Debian and Android. The drive of device can be microSD card, which can be purchased in our store.

 

Operating systems can be downloaded from the manufacturer's website.

The manufacturer also provides guide for the installation of the system.

Communication

Minicomputer has basic communication interfaces that can be found in office computers of PC class. In addition to the previously listed connectors of audio and video, the user has at his or her disposal:

  • a USB connector, to which can be connected, for example, a mouse, a keyboard, a wi-fi card or USB flash drive. If you find that the slots are too short, you can increase their number using an external USB HUB.
  • 40 pins of GPIO - outputs/inputs of general purpose that can be used to control the LEDs, buttons, drivers of motors. Among them are the pins that support interfaces: I2C, SPI and UART.
  • a slot for microSD - slot for memory microSD cards, on which installed can be the operating system.
  • microHDMI connector - sends the image to the monitor.

The device has: USB slot, microHDMI connector, Gigabit Ethernet and many others.

Power

As a power source, the system uses the microUSB connector. The manufacturer recommends that the voltage indicated on the connector had a value of 5.0 V and output current of the used power supply shall not be less than 2.0 A. In our assortment you will find power supplies that meet these parameters, for example: power supply Extreme 3.1 A.

Touch screens

In our offer, available are touch screens dedicated for minicomputers NanPi and NanoPC.

Wyświetlacz dla NanoPi

The screen connects through the tape cable, using dedicated LCD slot.

Starter set

The manufacturer has prepared a set of sensors and modules in a convenient chest that simplifies getting started with minicomputer.

Matrix Starter Kit - zestaw startowy dla NanoPi i Raspberry PiThe contents of the set Matrix Starter Kit - sold separately.

Specification

ModelNanoPi Fire3
Specification
ProcessorSamsung S5P6818
The core

Quad-Core ARM Cortex A9

Systems

Debian Android

Clock frequency1.4 GHz
RAM

1 GB DDR3 32-bit

Memory

microSD card

Slot for GPIO

40-pin, compatible with Raspberry Pi,

specification

Power

5 V / 2 A - microUSB

Board sizes75 x 40 mm
Interfaces
USB-Host

1 x USB 2.0

Network interfaceEthernet Gigabit
VideomicroHDMI 1.4 A, 1080p 60fps
Audio

microHDMI

Camera

DVP, slot of 0.5 mm FPC

LCDslot of 0.5 mm SMT FPC (RGB 8-8-8)
Communication

UART, SPI, I2C, GPIO, PWM

The debugger

Serial port of 4pin / 2.54 mm

Other

the Power and Reset buttons

status LEDs

Included

radiator, user manual

 

  • UC - Microkontroler S5P6818
  • UC - Core Cortex A53
  • UC - RAM 1 GB
  • UC - core 8. Octa Core
  • UC - Digital pins: 40
  • UC - External memory SD card
  • UC - freq: 1.4 GHz
  • UC - Ethernet: yes
  • UC - USB: 1x USB
  • UC - HDMI yes
  • UC - I2C yes
  • UC - UART yes
  • UC - Connector: 5V microUSB
  • UC - SPI interface yes
  • UC - LCD interface yes
  • UC - Camera interface yes
  • UC - Linux yes
  • UC - Android yes
  • UC - Windows no