• EOL

Soldering station 2in1 hotair and soldering iron WEP 878A - 700W

Index: LUT-01863 EAN: 5907558240177

Tip-based soldering iron and hot air iron in one. The total capacity of the station is 700 W. The device is equipped with adjustable temperature: hotair from 100 °C to 480 °C, tip-based from 200 °C to 480 °C. It automatically goes into standby mode after several minutes of inactivity.

Soldering station 2in1 hotair and soldering iron WEP 878A - 700W
€67.90
€55.20 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: WEP

Attention!

The product has been discontinued. Check other products in category.

Description

Temperature control of air flow and power control of air flow is realized with knobs. The temperature of the soldering iron is set with smaller knobs.

 

Stacja lutownicza hotair i grotowa WEP 878A - 700W

The station has a sensor in the base of the iron, with it when you put the iron down, the device cools a heating element from 3 to 8 minutes, and then it turns off (switches to standby mode). This procedure allows you to save energy, increase service life, and, above all, ensures greater safety. After reaching the standby mode, the station can be completely switched off with the button or to activate holding up the iron.

 

The station is used on the electronic repair services for safe soldering out QFP, BGA, SMD,PLCC, and othertemperature-sensitive elements.

 

Check out our offer of additional tips!

Specification

  • Supply voltage: 230 V / 50 Hz (network)
  • Power: 700 W
  • The station is controlled by the microcontroller which ensures a high stability
  • The device has a standby mode
  • The station has an ergonomical body
  • Temperature control and power supply using the knobs.

 

Hotair Soldering Iron

  • Adjustable temperature hot air from 100°Cto 480 °C
  • Temperature stability: +/- 1 °C
  • Temperature setting buttons
  • Smooth regulation of air flow by means of buttons
  • Air consumption: max. up to 120 litres/minute
  • The head size of the hot air 22 mm (all nozzles from the station of the PT / Aoyue)

 

Soldering Iron Tip-base

  • The bulb 907A
  • Adjustable temperature soldering tip: 200°Cto 480 °C
  • Temperature stability: +/- 2 °C
  • Soldering iron power: 60 W
 

Includes:

  • Soldering station WEP 878A
  • Stand for the hotair iron
  • Set of nozzles:
    • round nozzle with a diameter of 7 mm
    • round nozzle with a diameter of 9 mm
    • square 12 x 12 mm
  • Stand for the tip-based iron along with a cleaning sponge
  • Soldering iton 907A with the T-I tip
  • A gripper for lifting circuit

 

First run

  • You should not run the device immediately after delivery.
  • Equipment must remain for about 12 hours at room temperature before switching on.
  • All complaints caused by running of the equipment too soon will be denied.
  • You must completely remove the screw/screws from the bottom station if the source of air supply is the compressor. These screws are marked in red (1 or 3 screws depending on model).

 

Note

Heating elements (heaters) and the tips are not subject to warranty, and you must purchase new ones.

Our range of accessories for soldering:

Voltage to 220 V AC
Voltage from 240 V AC
Voltage nominal 230 V AC
Nominal power 700 W
Temperature 200 - 480 °C
Solder - Fan no
Solder - real temperature reading no
Solder - Hotair yes
Solder - Type A/C analog
Laboratory of the future Compatible
Package width 17 cm
Package height 27 cm
Package depth 15 cm
Package weight 2.45 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: