- EOL
|
Attention! The product has been discontinued. Check others products incategory. |
Description
MinicomputerNanoPi, version Fire3with processor S5P6818 Samsung octa-core ARM Cortex-A53 with a clock frequency of 1.4 GHz. The board has1GB of DDR3 RAM, aGigabit Ethernetport,microHDMI connector andUSB A slot, 40 GPIOsand a slot for microSDcards. It works withAndroid and Debian.
What it takes to run minicomputer NanoPi?
- MicroSD memory card - carrier, on which the operating system will be installed.
- AC adapter with DC plug - 5 V with current of 2 A.
- MicroHDMI cable - to connect the device to the monitor.
- Mouse and keyboard - to control and input the data into the device.
Operating system
NanoPi works with theDebian and Android. The drive of device can be microSD card, which can be purchased in our store.
|
Operating systems can be downloaded fromthe manufacturer's website. The manufacturer also providesguide for the installation of the system. |
Communication
Minicomputer has basic communication interfaces that can be found in office computers of PC class. In addition to the previously listed connectors of audio and video, the user has at his or her disposal:
- a USB connector,to which can be connected, for example, a mouse, a keyboard, a wi-fi card or USB flash drive. If you find that the slots are too short, you can increase their number usingan external USB HUB.
- 40 pins of GPIO - outputs/inputs of general purpose that can be used to control the LEDs, buttons, drivers of motors. Among them are the pins that support interfaces: I2C, SPI and UART.
- a slot for microSD - slot for memory microSD cards, on which installed can be the operating system.
- microHDMI connector- sends the image to the monitor.
The device has: USB slot, microHDMI connector, Gigabit Ethernet and many others.
Power
As a power source, the system uses the microUSB connector. The manufacturer recommends that the voltage indicated on the connector had a value of 5.0 V and output current of the used power supply shall not be less than 2.0 A. In our assortment you will find power supplies that meet these parameters, for example: power supply Extreme 3.1 A.
Touch screens
In our offer, available are touch screens dedicated for minicomputers NanPi and NanoPC.
The screen connects through the tape cable, using dedicated LCD slot.
Starter set
The manufacturer has prepared a set of sensors and modules in a convenient chest that simplifies getting started with minicomputer.
The contents of the setMatrix Starter Kit- sold separately.
Specification |
|
| Model | NanoPi Fire3 |
| Specification |
|
| Processor | Samsung S5P6818 |
| The core |
Quad-Core ARM Cortex A9 |
| Systems |
Debian Android |
| Clock frequency | 1.4 GHz |
| RAM |
1 GB DDR3 32-bit |
| Memory |
microSD card |
| Slot for GPIO |
40-pin, compatible with Raspberry Pi, |
| Power |
5 V / 2 A - microUSB |
| Board sizes | 75 x 40 mm |
| Interfaces | |
| USB-Host |
1 x USB 2.0 |
| Network interface | Ethernet Gigabit |
| Video | microHDMI 1.4 A, 1080p 60fps |
| Audio |
microHDMI |
| Camera |
DVP, slot of 0.5 mm FPC |
| LCD | slot of 0.5 mm SMT FPC (RGB 8-8-8) |
| Communication |
UART, SPI, I2C, GPIO, PWM |
| The debugger |
Serial port of 4pin / 2.54 mm |
| Other |
the Power and Reset buttons status LEDs |
| Included |
radiator, user manual |
Useful links |
