• EOL

Qik 2s9v1 Dual Serial Motor Controller - Pololu 1110

Index: PLL-13730 EAN: 5904422342074

Dual channel DC motor controller allows you to control the speed and direction of rotation of the motor using a simple serial interface, allowing simple connection of the controller to a microcontroller or computer. Supply voltage for motors is from 4.5 V to 13.5 V, the maximum current up to 1 A. Power supply for the logic part is from 2.7 V to 3.3 V.

Qik 2s9v1 Dual Serial Motor Controller - Pololu 1110
€22.50
€18.29 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Pololu
Compatibility: Arduino Raspberry Pi

Attention!

The product has been discontinued. Check other products in category.

Product description: Qik 2s9v1 two channel motor controller 13.5 V / 1 A - Pololu 1110

Second generation of Qik2s9v1dual channelDC motordriver allows you tocontrol speedanddirection of rotation ofa motor using a simpleserial interface, enabling simple connection of the driver to a microcontroller (e.g. Arduino), computer with serial port (externalRS-232 level converterrequired) or USB - Serial adapter. Supply voltage for the motors rangesfrom 4.5 V to 13.5 V, maximum currentup to 1 A. Power supply for the logic part is:2.7 V to 5.5V.

It provides ultrasonic 8-bit PWM speed control via a bidirectional serial protocol that offers automatic baud rate detection up to 38.4 kbps and optional CRC error checking. Two statusLEDsprovide visual feedback on the serial connection and any errors encountered for easy debugging, and a demonstration mode allows easy verification of proper operation.

Product compatible with Arduino

The manufacturer provides alibrary for Arduino.

Differences from previous version and competing products:

  • High frequency PWM (ultrasonic), eliminates the noise coming out of the motor
  • Fast communication protocol
  • Visible LEDs and demonstration mode
  • Protection against reverse motor power supply

Main features

  • Bidirectional control of two DC motors
  • Motor supply: 4.5 V to 13.5 V
  • Maximum continuous current: 1 A (3 A momentary)
  • Logic power supply: 2.7 V to 5.5 V
  • Optional automatic baudrate range detection
  • Two status LEDs
  • Serial error output
  • Demo mode - with jumpers allows initial testing without program
  • Optional CRC error detection, caused by noise or software errors
  • Optional motor shutdown in case of serial error or timeout
  • Supports module linking, allowing multiple motors and servos to be controlled over a single serial line
  • Comprehensive user guide

Outputs

PIN Description
GND Ground potential of the logic part.
VCC Power supply of the logic part - from 2.7 V to 5.5 V.
RX UART receiver pin.
TX Pin of UART transmitter.
RESET Optional Reset pin, activated by providing a low state.
ERR Output associated with the red LED.
M1 Output to connect a second motor.
M0 Output to connect the first motor.
GND . Ground potential of the motors supply.
VMOT Power supply for the motors - from 4.5 V to 13.5 V.
Status LED (green) Status green LED to indicate power supply.
Demo-mode jumper Jumper to enter demo mode.
Fixed-baid jumper The jumper sets the baud rate to 38.4 kbps.
CRC jumper The jumper that activates CRC mode.
Error LED (red) Status red LED to indicate an error.

Qik 2s9v1 dwukanałowy sterownik silników 13,5V/1A - Pololu 1110

Qik 2s9v1 dual channel motor controller - Pololu 1110 and accessories.

Specification Qik 2s9v1 2-channel motor controller 13.5 V / 1 A - Pololu 1110

  • Chip: TB6612FNG
  • Number of channels: 2
  • Motor supply voltage: 4.5 V to 13.5 V
  • Continuous output current per channel: 1 A (momentary 3 A)
  • Baud rate range: 1200 bps - 38400 bps
  • Correct baud rate: 38400 bps
  • Available PWM frequencies: 3.1 5 kHz / 15.7 kHz / 7.8 kHz / 3.9 kHz
  • Logic voltage supply: 2.7 V to 5.5 V
  • Current consumption for the logic unit: up to 15 mA
  • Protection against reverse polarity of the motor connection
  • Dimensions: 30,5 x 18 mm
  • Weight: 2 g

Set contains

  • Qik 2s9v1 motor driver
  • strip goldpin 16 x 1 - pin
  • strip goldpin 12 x 1 - pin
  • 2x goldpin strip 2 x 1 - pin
  • 2x jumpers
Voltage to 4.5 V
Voltage from 13.5 V
Current 1 A
Channels 2

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: