• Reduced price

TB67H420FTG Dual/Single Motor Driver Carrier - Pololu 2997

Index: PLL-12059 EAN: 5904422318468

Single channel DC motor controller. Continuous current per channel 2.6 A (momentary up to 5 A). Supply voltage from 4.5 V to 28 V.

TB67H420FTG Dual/Single Motor Driver Carrier - Pololu 2997
€13.90 -12%
€12.23
€9.94 tax excl.
Lowest price 30 days: €11.73
Available
Shipping in 24 hours
PayPal payment
Manufacturer: Pololu
Compatibility: Arduino Raspberry Pi

Product description: TB9051FTG - single channel motor controller 28V/2,6A - Pololu 2997

The modulebased on theTB9051FTGchip allows you tocontroloneDC motor. The motor can be supplied with voltagefrom 4.5V to 28Vwith continuous current up to 2.6A, momentary (for a few seconds) up to 5A. We recommend reading theTB9051FTGdocumentation before use.

Pinouts of one-channel controller

Wyprowadzenia sterownika Pololu

PIN Description
Vin Motor supply voltage from 4.5 V to 28 V. It has protection against polarity change of supply voltage.
GND System ground potential.
VM Output providing access to the motor power supply after reverse polarity protection. It can be used to power other components of the system.
OUT1 Outputs - to connect the motor leads.
OUT2
Outputs - to connect the motor leads.
VCC Logic voltage - 5 V.
OCC In case of overcurrent, the controller is switched off. By default in low state. If it is in high state it will automatically try to resume operation after a short time interval.
EN When in the low state, the OUT1 and OUT2 outputs are set to the high impedance state. Inverted Inverted PWM can be applied to this pin(When EN is in the high state and PWM1 or PWM2 in the high state).Default is in the low state.
ENB When it is in high state,OUT1 and OUT2 outputs are set to high impedance state.PWM can be applied to this pin(When ENB is in low state and PWM1 or PWM2 in high state).Default inhighstate.
PWM1 Control input for OUT1. Default is low.
PWM2 The control input for OUT2. Default low.
OCM Current monitoring output, pin provides an analog feedback voltage of approximately 500 mV per amplifier.
DIAG Error diagnostics output. goes low when errors occur or the controller is disabled by EN or ENB.

Connecting the controller with a DC motor

Sterownik silników Pololu

Table for PWM1 + PWM2 mode

Input Output Operation mode
EN ENB PWM1 PWM2 OUT1 OUT2
1 0 PWM 0 PWM(H/L) L

Forward speed/brake speed

at the speed specified: PWM %

1 0 0 PWM L PWM(H/L)

Reverse/Brake

at the speed specified: PWM %

1 0 0 0 L L Stop, outputs connected to ground
1 0 1 1 L L
0 X X X Z Z Free runningOutputs disconnected
X 1 X X Z Z

Table for PWM1 + PWM2 + EN mode

Input Output Operation mode
EN ENB PWM1 PWM2 OUT1 OUT2
PWM 0 1 0 PWM(H/Z) PWM(L/Z)

Forward speed/Free speed

at the speed specified: PWM %

0 1 PWM(L/Z) PWM(H/Z)

Reverse speed/Free speed

at the speed specified: PWM %

0 X X X Z Z Free runningOutputs disconnected
X 1 X X Z Z

Scheme of the system

The circuit includes thecontrollerand the necessary passive elements for its proper operation. The electronic schematic is available on the drawing below.

Schemat sterownika silników pololu

Technical specifications of the controller from Polol

  • Single-channelmotorcontroller
  • Supply voltage of the motor: from 4.5 to 28 V
  • Output current: 2.6 A (5 A momentary)
  • Automatic current limitation function helps prevent overheating by gently reducing the voltage instead of abruptly shutting down
  • Under-voltage, short-circuit and overheat protection
  • Protects against polarity reversal of the supply voltage
  • Dimensions: 25.4 x 25.4 mm

Voltage to 4.5 V
Voltage from 28.0 V
Current 2.5 A
Channels 1
Package width 8.5 cm
Package height 0.6 cm
Package depth 11 cm
Package weight 0.007 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: