• EOL

NanoPi M2A - Samsung S5P4418 Quad-Core 1,4GHz + 1GB RAM - WiFi + Bluetooth 4.0

Index: NNP-08583 EAN: 5904422311865

Minicomputer NanoPi with processor Samsung S5P4418 quad-core ARM Cortex-A9 with a clock frequency of 1.4 GHz. Board has 1GB of DDR3 RAM, integrated wi-fi and Bluetooth 4.0, an Ethernet Gigabit port, HDMI connector and two USB A slot + 2 x USB Host on pins of 2.54 mm, 40 GPIOs, slot for microSD cards. It works with the uboot, Android and Debian.

NanoPi M2A - Samsung S5P4418 Quad-Core 1,4GHz + 1GB RAM - WiFi + Bluetooth 4.0
€62.50
€50.81 tax excl.
Manufacturer: FriendlyARM

Attention!

The product has been discontinued. Check other products in category.

Description

MinicomputerNanoPi, version M2Awith processor Samsung S5P4418 quad-core ARM Cortex-A9 with a clock frequency of 1.4 GHz. Board has1GB of DDR3 RAM, integratedwi-fi and Bluetooth 4.0, anEthernet Gigabit port,HDMI 1.4A connectorandtwo USB A slot+2 x USB Hoston pins of 2.54 mm,40 GPIOs, slot for microSDcards. It works with theuboot, Android and Debian.

NanoPi M2A has a Ethernet Gigabit port, WiFi and 802.11 b/g/n Bluetooth 4.0 dual-mode module with built-in antenna.

 

NanoPi M3 - Samsung S5P6818 Octa-Core
The advantage of board, is its small size, the outline fits in a rectangle with sides of 64 x 60 mm.

What it takes to run minicomputer NanoPi?

 

Operating system

NanoPi works with the systems selected by manufacturer: u-boot and UbuntuCore. The drive of device can be microSD card, which can be purchased in our store.

 

Operating systems can be downloaded from the manufacturer's website.

The manufacturer also provides guide around the installation of the system.

Communication

Minicomputer has basic communication interfaces that can be found in office computers of PC class. In addition to the previously listed connectors of audio and video, the user has at his or her disposal:

  • two USBconnectorsA +2x USB Host on pins of 2.54 mmto which can be connected, for example, a mouse, a keyboard, a wi-fi card or USB flash drive. If you find that the slots are too short, you can increase their number using an external USB HUB. The interfaces displayed on pinach can be connected using wires.
  • EthernetGigabit slot, that is, the ability to directly connect to the LAN network.
  • the wi-fi module -it allows for communication with wireless 802.11 b/g/n network.
  • Bluetooth 4.0 module- it enables the data transmission through the popular interface.
  • 40 pins of GPIO - outputs/inputs with general purpose that can be used to control the LEDs, buttons, drivers of motors. Among them are the pins supporting interfaces: I2C, SPI and UART.
  • a slot for microSD  - slot for memory card microSD on which the operating system can be installed.
  • HDMI connector- it transfers image to the monitor.

The device has 2 USB slots, HDMI connector, audio Jack of 3.5 mm, an Ethernet port and many others.

Power

As a power source, the system uses the microUSB connector. The manufacturer recommends that the voltage indicated on the connector had a value of 5.0 V and output current of the used power supply shall not be less than 2.0 A. In our assortment you will find power supplies that meet these parameters, for example: power supply Extreme 3.1 A.

Minicomputer NanoPi M2A in comparison with the popularRaspberry PiBoard andArduino.

Touch screens

In our offer, available are touch screens dedicated for minicomputers NanPi and NanoPC.

Wyświetlacz dla NanoPi

The screen connects through the tape cable, using dedicated LCD slot.

Starter set

The manufacturer has prepareda set of sensors and modulesin a convenient chest that simplifies getting started with minicomputer.

Matrix Starter Kit - zestaw startowy dla NanoPi i Raspberry Pi

The contents of the setMatrix Starter Kit- sold separately.

 

Specification

Model NanoPi M2A
Specification
Processor Samsung S5P4418
The core

Quad-Core ARM Cortex A9

Systems

Debian

Android

uboot

Clock frequency 1.4 GHz
RAM

1 GB DDR3 32-bit

Memory

microSD card

Power system

AXP228 PMU

Slot for GPIO

40-pin, compatible with Raspberry Pi

Power

5 V / 3 A - microUSB

Board sizes 64 x 60 mm
Interfaces
USB-Host

2x USB A slots

2x USB Host on pins of 2.54 mm

Network interface Gigabit Ethernet (RTL8211E)
The Wi-Fi interface module wi-fi 802.11 b/g/n with antenna
Bluetooth interface
Bluetooth 4.0 dual mode
Video HDMI 1.4 A, 1080p 60fps
Audio

HDMI, audio Jack 3.5 mm

Camera DVP, slot of 0.5 mm FPC
LCD slot of 0.5 mm SMT FPC (RGB 8-8-8)
LVDS interface 20 pin, pitch of 2.0 mm
Communication

UART, SPI, I2C, GPIO, PWM

The debugger

Serial port of 4pin / 2.54 mm

Other

the Power and Reset buttons

status LEDs

 

 

UC - Microcontroller S5P4418
UC - Core Cortex A9
UC - RAM 1 GB
UC - core 4. Quad Core
UC - Digital pins 40
UC - External memory microSD card
UC - freq 1.4 GHz
UC - Ethernet yes
UC - WiFi yes
UC - USB 2x USB
UC - Bluetooth yes
UC - HDMI yes
UC - I2C yes
UC - UART yes
UC - Connector 5V microUSB
UC - SPI interface yes
UC - LCD interface yes
UC - Camera interface yes
UC - Linux yes
UC - Android no
UC - Windows no
Package width 12 cm
Package height 3 cm
Package depth 18 cm
Package weight 0.1 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: