- EOL
|
Attention! The product has been discontinued. Check others products incategory. |
Description
MinicomputerNanoPi in a version S2with theSamsung processor S5P4418 quad-core ARM Cortex-A9with a clock frequency of1.4 GHz. The board has1GBof DDR3 RAM memory,8 GB of eMMC,wi-fimodule,Bluetooth,USB slot,microHDMI,3.5 mm Jack,40 GPIOsand a connector for microSD card. It works with theAndroid and Debian.
The advantage of this board, is its small size, the outline fits in a rectangle with sides of 75 x 40 mm.
What it takes to run minicomputerc NanoPi?
- The AC adapter with a microUSB plug - 5 V with current of 2 A
- Cable microHDMI- to connect the device with the monitor
- Mouse and keyboard - to control and input data into the device
- MicroSD memory card - carrier, on which installed will be operating system (optional)
Operating system
NanoPi works with Debian and Android. The drive of the device may be microSD card which can be purchased in our store, or internal memory eMMC of 8GB (by default, installed is the system Debian LXDE 8.1).
|
Operating systems can be downloaded fromthe manufacturer's website. The manufacturer also providesguide for the installation of the system. |
Communication
Minicomputer has basic communication interfaces that can be found in office computers of PC class. In addition to the previously listed connectors of audio and video, the user has at his or her disposal:
- a USB connector to which can be connected, for example, a mouse, a keyboard, a wi-fi card or USB flash drive. If you find that the slots are too short, you can increase their number usingan external USB HUB.
- module wi-fi 802.11 b/g/n- it allows you to wirelessly connect to the network
- Bluetooth 4.0 module for wireless transmission, for example, with a smartphone
- 40 pins of GPIOoutputs/inputs of general purpose that can be used to control the LEDs, buttons, drivers of motors. Among them are the pins that support interfaces: I2C, SPI and UART.
- a slot for microSD - slot for microSD memory cards, on which installed can be the operating system.
- 3.5 mm Jack connector- it transmits sound to headphones or speakers.
- microHDMI connector- it transmits the image to the monitor.
Device features: USB connector, connector microHDMI, 3.5 mm Jack and many others.
Power
As a power source, the system uses the microUSB connector. The manufacturer recommends that the voltage indicated on the connector had a value of 5.0 V and current of the used power supply shall not be less than 2.0 A. In our assortment, you will find power supplies that meet these parameters, for example: power supply Extreme 2.1 A.
Touch screens
In our offer available are touch screens dedicated for minicomputers NanPi and NanoPC.
The screen connects through the tape cable, using dedicated LCD slot.
Starter set
The manufacturer has prepareda set of sensors and modulesin a convenient chest that simplifies getting started with minicomputer.
The contents of the setMatrix Starter Kit- sold separately.
Specification |
|
| Model | NanoPi S2 |
| Specification |
|
| Processor | Samsung S5P4418 |
| The core |
Quad-Core ARM Cortex A9 |
| Systems |
Debian Jessie 8 Android 5.1 |
| Clock frequency | 1.4 GHz |
| RAM |
1 GB DDR3, 32-bit |
| Memory |
built-in 8 GB of eMMC microSD card |
| Slot for GPIO |
40-pin compatible with Raspberry Pi |
| Power |
5 V / 2 A - microUSB |
| Board sizes | 75 x 40 mm |
| Interfaces | |
| USB Host |
1 x USB 2.0 |
| Network interface | Wi-fi |
| Video | microHDMI 1.4 A, 1080p 60fps |
| Audio |
microHDMI, 3.5 mm Jack |
| Camera |
DVP, slot of 0.5 mm FPC, 24 pins LVDS, slot of 0.5 mm FPC, 24 pins |
| LCD | slot of 0.5 mm SMT FPC (RGB 8-8-8) |
| Communication |
UART, SPI, I2C, GPIO, PWM, Bluetooth |
| The debugger |
Serial port of 4pin / 2.54 mm |
| Other |
The Power and Reset button status LEDs A/C converter the antenna u.FL connector |
Useful links
|
