- EOL
|
Attention! The product has been discontinued. Check others products incategory. |
Description
Miniature computerNanoPi, versionNeo v1.3 with processorAllwinner H3 quad-coreARM Cortex-A7 with a clock frequency of 1.2 GHz. Tile has512 MBof memoryRAM DDR3, built-in portEthernetandUSB slot + 2x USB Host on pins 2.54 mm,36 GPIO, connector for card microSD. Works with systems from manufacturer - u-boot and UbuntuCore.Hassoldered connectors goldppin.
The advantage of tile is its small size, the dimension of the tiles is 40 x 40 mm.
Soldered connectors provide an instant connection of sensors.
What it takes to run minicomputer NanoPi?
- MicroSD memory card - carrier on which the operating system will be installed
- The AC adapter with a micro usb connector- 5 V with maximum load current of 2 A
The device has a USB plug connector and an Ethernet port and many others.
Operating system
NanoPi works with the systems prepared by the manufacturer: u-boot and UbuntuCore. The drive of device may be microSD card, which can be purchased in our store.
|
Operating systems can be downloaded fromthe manufacturer's website. The manufacturer also provides guide on the installation of the system. |
Communication
Minicomputer has communication interfaces that can be found in office computers of PC class. In addition to the previously listed connectors for audio and video, the user has at his or her disposal:
- 1x USB A connector + 2x USB Host on pins 2.54 mm, to which can be connected, for example, a mouse, a keyboard, a wi-fi card or USB flash drive. If you find that the slots are too short, you can increase their number usingan external USB HUB. The interfaces displayed on pins can be connected using wires.
- Ethernet slot, that is the ability to directly connect to the network.
- GPIO x 36 pin - outputs/inputs with general purpose that can be used to control the LEDs, buttons, drivers of engines. Among them are the pins supportting interfaces: I2C, SPI and UART.
- a slot for microSDslot for memory card microSD on which can be installed the operating system.
The distribution of the GPIO pins - pins have to be self-solderd,strips goldpin raster of 2.54 mmcan be purchased in our store.
Power
As a power source, the system uses the microUSB connector. The manufacturer recommends that the voltage indicated on the plug had a value of 5.0 V and an output current of the used power supply shall not be less than 2.0 A. In our offer, you will findpower supplies that meet these parameters, for example:power supply Extreme 2.1 A.
In our offer, you will also find special radiator.
Starter set
The manufacturer has prepareda set of sensors and modulesin a convenient chest that simplifies getting started with minicomputer.
The contents of the setMatrix Starter Kit- sold separately.
Specification |
|
| Model | NanoPi Neo |
| Specification |
|
| Processor | Allwinner H3 |
| The core |
Quad-Core ARM Cortex A7 |
| Systems |
u-boot UbuntuCore |
| Clock frequency | 1.2 GHz |
| RAM |
512 MB |
| Memory |
microSD card |
| GPIO slot |
36-pin connector |
| Power |
5 V / 2 A - microUSB |
| Tile sizes | 40 x 40 mm |
| Interfaces | |
| USB-Host |
1 x USB A socket 2 x USB Host on pins 2.54 mm |
| Network interface | Ethernet 10/100 Mbps |
| Video | - |
| Audio |
audio output and microphone out on the GPIO connector |
| Communication |
UART, SPI, I2C, GPIO, PWM |
| The debugger |
Serial port 4pin / 2.54 mm |
| Additional |
Built-in led |
Useful links |
