• EOL

ITG-3200 3-axis I2C digital gyroscope module - SparkFun SEN-11977

Index: SPF-02106 EAN: 5903351247689

Sensor to measure angular velocity in three axes: X, Y, Z. The measurement range is ± 2 °/sec. The module is powered with the voltage in the range from 2.1 V to 3.6 V, it has a built-in temperature sensor that communicates via I2C bus.

ITG-3200 3-axis I2C digital gyroscope module - SparkFun SEN-11977
€20.50
€16.67 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: SparkFun
Compatibility: Arduino

Attention!

The product has been discontinued. Check other products in category.

Description of product: SparkFun ITG-3200 3-axis digital I2C gyroscope

Sensor ITG-3200 allows for the measurement of angular velocity in three axes: X,Y,Z in the range of ± 2 °/secwith a resolution of16 bits. The module is powered with the voltage in the range from 2.1 to 3.6 V. For communication with the central unit, it uses the popularI2C bus(TWI) which can operate at speeds up to 400 MHz. In addition, the system is equipped with a digital thermometer.

 

The product is compatible with Arduino

The manufacturer has prepared a user manual for connection to the Arduinoalongwith the library on GitHubandthe sample program in the C languagefor the Atmega328 microcontroller.

3-osiowy żyroskop cyfrowy

3-axis digital gyroscope.

 

Since the maximum voltage with which the system works, is 3.4 V, for working with Arduino, needed is a voltage converter. The exceptions are the modules operating with voltages of 3.3 V, for example,Arduino Pro Mini 328 - 3.3 V/8 MHz.

 

 

Pins

The sensor has seven pins for the installation of the goldpin straps - pitch of 2.54 mm (not included). Soldered connectors provide the connection of the sensor viawires or direct attachment to the breadboard.

 

Name

Description

VCC The supply voltage from 2.1 V to 3.6 V.
GND The groundof the system.
VIO Reference voltage of the high status on the pins of the I2C bus.
INT The external interrupt's output - open drain (details indocumentation) .
CLK The sync output. Not used, should be connected to ground (e.g. creating a jumper on the back of the board).
SDA The data line of the I2C bus (TWI).
SCL The clock line of the I2C bus (TWI).

 

 

Communication - I2C bus

The sensor communicates digitally via the two-wire I2C bus (TWI). Jumper on the front of the board, marked as AD0 through a connection with GND or VCC to change the bus address. By default, it is connected to VCC which sets the address to the value of 0x69.

 

The sensor is also frequency - synchronization CLK input, if not used, it must be connected to ground (e.g. creating a jumper on the back of the board).

Specification of the digital gyroscope

  • Supply voltage: 2.1 V - 3.6 V
  • Current consumption: approx. 6.5 mA (5 µA in standby mode)
  • Three axes: X, Y, Z
  • Communication interface: I2C (TWI) - 400 kHz
  • Resolution: 16-bits for each axis
  • Measurement range: ± 2 °/sec
  • Integrated,programmable low-pass filter
  • Built-in digital temperature sensor
  • The ability to connect an external resonator (32.768 kHz or 19.2 MHz)
  • Pins: holes forgoldpin connectors- 2.54 mm pitch
  • Board sizes: 22.2 x 18.5 mm

 

Package width 6 cm
Package height 8 cm
Package depth 0.1 cm
Package weight 0.002 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: