• EOL

GSM-3G-SIM-card - d-u3G μ-v shield.1.13 - for Arduino and Raspberry Pi connector U.FL

Index: RPI-07465 EAN: 5904422335816

The module supports communication in GSM 900 MHz / 1800 MHz and UMTS 900 MHz / 2100 MHz. It allows for voice calls, sending SMS messages. On the board are: connector of SIM card, powering module for battery LiPol, as well as POWER and RESET buttons. Version works with Arduino and Raspberry Pi, it has a connector for antenna u.FL.

GSM-3G-SIM-card - d-u3G μ-v shield.1.13 - for Arduino and Raspberry Pi connector U.FL
€83.90
€68.21 tax excl.
The minimum purchase order quantity for the product is 50.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Itbrain Power
Compatibility: Arduino Raspberry Pi

Attention!

The product has been discontinued. Check other products in category.

Description

The module working withArduinoandRaspberry Pi (in version 3B, 2B, B+ and A+)that provides communication in GSM 900 MHz / 1800 MHz and UMTS 900 MHz / 2100 MHz. It allows for voice calls, sending SMS messages. On the board are: connector of SIM card, powering module for battery LiPol, as well as u.FL slot to mountan external antenna.

 

The system works withArduinoandRaspberry Pi (in version 3B, 2B, B+ and A+), it has a connector u.FL to connectan external antenna. In our offer, you will also findthe module with u.fl connectorand specialvoltage converters.

 

Moduł GSM 3G SIM - d-u3G μ-shield v.1.13 - do Arduino i Raspberry Pi - złącze u.FL

The distribution of elements on the board d-u3G μ-shield. 

Specification

  • Driver: Quectel UG95F
  • Supported standards: GSM / UMTS
  • Frequencies:
    • GSM: 900 / 1800 MHz
    • UMTS: 900 / 2100 MHz
  • One SIM connector
  • The antenna u.FL connector
  • Digital audio interface
  • Built-in converter USB to UART (USB connector can be used to power the module)
  • Automatic selection of logic levels between 3 V to 5 V
  • Buttons of modem Power and Reset
  • Works withArduinoandRaspberry Pi, along with sample codes of manufacturer
  • Two mounting holes with diameter of: 2.5 mm
  • Board sizes: 40 x 35 mm

 

Detailed module description can be found in the user guide in part firstandsecond, and on the website of the manufacturer.

Pins

 

Pin Description
SLP The sleep pin is activated by the high state.
CTS Input Clear to Send - details indocumentation.
RTS Output Ready to Send - details indocumentation.
STATUS The status pin.
RI The output Ring Indicator - details indocumentation.
GROUND The ground of the system.
Vcc 4V IN/OUT Input/output 4 V. When using battery, you need to include a LED (e.g., 1N14148) between the positive pole of battery and BkBat+ on the board, the anode heading the battery.
Vin 5V LiPol IN Input 5 V to charge with a LiPol battery.
Vusb 5V OUT The output is 5 V.
POWER ON The control of a supply voltage of the system GSM (On/Off).
RESET GSM system reset.
TX (RXD) Communication via the serial interface.
RX (TXD) Communication via the serial interface.
LiPol +/- Connecting the battery LiPol, respectively "+" and "-".
ANTENNA CONNECTOR UFL OR SMA Antenna connector, depending on version of the SMA or u.FL.
DIGITAL AUDIO Mass for analog audio ports.
Backup bat +/- Backup battery, respectively "+" and "-". When using the battery, you need to include a LED (e.g., 1N14148) between the positive pole of battery and BkBat+ on the boar, the anode heading the battery.

 

The connection to the Arduino

The system works with Arduino Uno using the following pins:

 

Pin Arduino Description
GSM RX D3 Communication via the serial interface.
GSM TX D2 Communication via the serial interface.
RESET D6 GSM system reset.
POWER ON D7 The control of a supply voltage of the system GSM (On/Off).
VIN (5 V LiPol) 5 V

Power supply 5 V. Details of the connection in the battery LiPol case, are available inthe manufacturer's manual.

GND

GND The ground of the system.

STATUS

D5 The status pin.

 

Check out the example project for Arduino -home alarm system!

 

Connect to the Raspberry Pi

The purpose of the launch module with the Raspberry Pi, you must perform the following connections:

 

Pin RPi Description
GSM RX 10

Communication via the serial interface (don't work in the USB communication).

GSM TX 08

Communication via the serial interface (don't work in the USB communication).

RESET 18 GSM system reset.
ON / OFF 16 The control of a supply voltage of the system GSM (On/Off).
VIN (5 V LiPol) 02/04 The supply voltage of 5 V.

GND

04/14 The ground of the system.
STATUS 12 The status pin.

 


Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: