• EOL

Module GSM GPRS dual SIM c-uGSM μ-v shield.1.13 - Arduino and Raspberry Pi connector U.FL

Index: RPI-05165 EAN: 5904422363192

The module supports GSM and GPRS communication. It allows for voice calls, sending SMS messages. On the board are: two connectors for SIM card, powering module for battery LiPol, as well as POWER and RESET buttons. Version works with Arduino and Raspberry Pi, it has a connector for antenna U.FL.

Module GSM GPRS dual SIM c-uGSM μ-v shield.1.13 - Arduino and Raspberry Pi connector U.FL
€36.50
€29.67 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Itbrain Power
Compatibility: Arduino Raspberry Pi

Attention!

The product has been discontinued. Check other products in category.

Description

The module working withArduinoandRaspberry Pi (in version 3B, 2B, B+ and A+)that provides communication in GSM and GPRS. It allows for voice calls, sending SMS messages and transfering data. On the board are: 2 connectors for SIM-cards, powering module for battery LiPol and a slot U.FL to mount an external antenna.

 

The system works withArduinoandRaspberry Pi (in version 3B, 2B, B+ and A+), it has a connector U.FL to connectan external antenna. In our offer you will also findthe module with SMA connectorand specialvoltage converters.

 

Moduł GSM GPRS dual SIM - Arduino i RaspberryThe distribution of elements on the Board c-uGSM μ-shield.

Specification

  • Driver: Quectel M95F
  • Supported standards: GSM / GPRS
  • Frequencies: 850 / 950 / 1800 / 1900 MHz
  • Support standard DTMF
  • Two connectors for SIM-cards (one connection is active at the moment)
  • The antenna connector U.FL
  • Audio interface
    • Output: 700 mV RMS
    • Input: capacitor MIC
  • Built-in Converter USB-UART (USB connector can be used to power the module)
  • Automatic selection of logic levels between 3 V to 5 V
  • Buttons of modem: Power and Reset
  • It works withArduinoandRaspberry Pi, along with sample codes of manufacturer
  • Two mounting holes with diameter of: 2.5 mm
  • Board sizes: 40 x 32 mm

 

Detailed module description can be found in the user guide in partfirstandsecond, and onthe website of the manufacturer.

 

Pins

Moduł GSM GPRS dual SIM - Arduino i Raspberry

Pin Description
CTS Input Clear to Send - details indocumentation.
RTS Output Ready to Send - details indocumentation.
STATUS The status pin.
RI The output Ring Indicator - details indocumentation.
GROUND The ground of the system.
Vcc 4V IN/OUT Input/output 4 V. When using battery, you need to include a LED (e.g., 1N14148) between the positive pole of battery and BkBat+ on the board, the anode heading the battery.
Vin 5V LiPol IN Input 5 V to charge with a LiPolbattery.
Vusb 5V OUT The output Is 5 V.
ON/OFF The control of a supply voltage of the system GSM (On/Off).
RESET GSM system reset.
TX (RXD) Communication via the serial interface.
RX (TXD) Communication via the serial interface.
LiPol  +/- Connecting the battery LiPol, respectively "+" and "-".
ANTENNA CONNECTOR UFL OR SMA Antenna connector, depending on version of the SMA or U.FL.
AGND Ground for analog audio ports.
SPK +/- Output to speakers, respectively "+" and "-".
MIC +/- Microphone's input, respectively, " + " and "-".
Backup bat +/- Backup battery, respectively "+" and "-". When using the battery, you need to include a LED (e.g., 1N14148) between the positive pole of battery and BkBat+ on the boar, the anode heading the battery.

The connection to the Arduino

The system works with Arduino Uno using the following pins:

 

Pin Arduino Description
GSM RX D3 Communication via the serial interface.
GSM TX D2 Communication via the serial interface.
RESET D6 GSM system reset.
ON / OFF D7 The control of a supply voltage of the system GSM (On/Off).
VIN (5 V LiPol) 5 V

Power supply 5 V. Details of the connection in the battery LiPol case, are available inthe manufacturer's manual.

GND

GND The ground of the system.

STATUS

D5 The status pin.

 

Check out the example of project for Arduino -home alarm system!

 

Connect to the Raspberry Pi

To launch the module with the Raspberry Pi, you must perform the following connections:

 

Pin RPi Description
GSM RX 10

Communication via serial interface (no connection at USB connection).

GSM TX 08

Communication via serial interface (no connection at USB connection).

RESET 18 GSM system reset.
ON / OFF 16 The control of a supply voltage of the system GSM (On/Off).
VIN (5 V Li-Pol) 02/04 The supply voltage of 5 V.

GND

04/14 The ground of the system.
STATUS 12 The status pin.

 

Package width 6 cm
Package height 0.8 cm
Package depth 6 cm
Package weight 0.01 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: