STSPIN220 Low-Voltage Stepper Motor Driver Carrier - Pololu 2876

Index: PLL-13822 EAN: 5904422321543

Stepper motor driver powered from 1,8 V to 10 V. Maximum resolution: 1/256 koku. Can operate without heat sink or forced air flow at 1.1 A per phase.

STSPIN220 Low-Voltage Stepper Motor Driver Carrier - Pololu 2876
€9.00
€7.32 tax excl.
Available
Shipping in 24 hours
PayPal payment
Manufacturer: Pololu
Compatibility: Arduino Raspberry Pi

Product description: Polol STSPIN220 - stepper motor controller

The system allows to control a singlebipolar stepper motor. It offers a wide range of step resolutions (from full to 1/256 steps). By setting the current-voltage parameters, higher step speeds are possible.

STSPIN220 works directly with 3.3 V and 5 V systems. The diagram below shows how to connect to a microcontroller.

Schemat połączenia sterownika silnika z mikrokontrolerem

The controller requires connection oflogical voltage (from 3 to 5 V)through VCC and GND outputs andmotor supplyvoltagefrom 1.8 Vto 10 V throughVIN and GND outputs. The power supplies should have appropriate decoupling capacitors located close to the board and should be able to deliver the expected currents. The system has protections against overheating, short circuit and exceeding the maximum current.

Polol STSPIN220 stepper motor controller specification

  • Minimum input voltage: 1,8 V
  • Maximum input voltage: 10 V
  • Continuous current per phase: 1.1 A
  • Maximum current per phase: 1,3 A
  • Minimum logical voltage: 1,6 V
  • Maximum logical voltage: 5,5 V
  • Microstep resolution: full, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256
  • Current limit control: potentiometer
  • Soldering pins included
  • Dimensions: 15.2 x 20.3 mm
  • Weight: 1,4 g

The step size is selected using M0 - M4 inputs. The table below shows how to obtain the appropriate step resolution. The current limit must be set low enough for proper operation of the controller modes. Otherwise, the intermediate current levels will not be properly maintained and the motor will skip the microsteps.

MODE1 MODE2 MODE3 (STEP) MODE4 (DIR) Resolution
Low Low Low Low Full step
High Low High Low Half step
Low High Low High 1/4 step
High High High Low 1/8th step
High Low High High 1/8th step
High High High High step 1/16
Low High Low Low 1/32 step
Low Low Low High 1/32 step (1)
High High Low High 1 / 64 step
Low High High High 1/64th step
High Low Low Low 1/128 step
Low Low High Low 1/128 step (1)
High High Low Low 1/256 step
Low High High Low 1/256 step
High Low Low High 1/256 step
Low Low High High 1/256 step (1)

(1) Maintaining low states on the inputs MODE1 and MODE2 after configuring the step resolution forces the controller to full step mode instead of the selected configuration.

STSPIN220 has 2 different inputs to control power, STBY /RESET and EN/FAULTstates:

  • low state on STBY pin: the controller enters low power mode, turns off the motor outputs and resets the translation table. Default high state on the STBY pin
  • the low state on the ENABLE pin turns on the motor by default

Current limitation

STSPIN supports active pad limitation for high jumping speeds. One way to set the current limit is to set the controller to full step mode and measure the current flowing through a single motor coil without STEP input timing. The measured current will be equal to the current limit.

Current limit = VREF x 5

Attention!

The coil current may be very different from the power supply current. When setting the current limit, use the current measured at the power supply.

If the controller operates in full crow mode, both coils will always be on and limited to 100% of the current setting.

If the controller operates in one of the microcontrol modes, the current flowing through the coils will change with each step from 0% to 100% of the set limit.

Schemat silnika krokowego

Voltage to 1,8 V
Voltage from 10 V
Current 1,1 A
Channels 1
Package width 8 cm
Package height 0.5 cm
Package depth 8.7 cm
Package weight 0.003 kg

Be the first to ask a question about this product!

Product reviews

STSPIN220 Low-Voltage Stepper Motor Driver Carrier - Pololu 2876

5/5

Average grade

2

Customers opinion
The following opinions are collected
and verified by
an external partner Trustmate
and come from the post-purchase process.

Zdjęcia użytkowników

Customers who bought this product also bought:

Products from the same category: