Categories

Pololu High-Power 18v15 - single-channel 30V / 15A motor controller

Based on the powerful MOSFET H bridge allows you to control engine rpm in both directions. Motor power supply: from 5.5 V to 30 V. max. Current: 15 A.

More details

PLL-00744

Dodano produkt do koszyka

In stock, shipping 24 hours!

Cena: 159,00 zł


Specification

  • Number of channels: 1
  • Voltage motor power supply: from 5.5 V to 30 V
  • Continuous motor current per channel: 15 A
  • Maximum PWM frequency: 40 kHz
  • The maximum voltage logic 5.5 V
  • The resistance of the MOSFET: 3.5 mω
  • Dimensions: 33 x 20.3 mm
  • Weight: 2.8 g (without connectors)
 
 

Description

Driver based on the MOSFET allows you to control one DC motor, powered by voltage from 5.5 V to 30 V with current consumption up to 15 A.

The slats were deployed on both sides of the module. After one of the connectors is responsible for the control and power supply of the logical part. On the opposite side is the power contacts of the motor (V+, GND) and outputs (OUT, OUTB). The voltage signals sterujacych should be in the range from 3.5 V to 5.5 V. the Manufacturer recommends does not work at the voltage of 3.3 V.

 

In a standard installation requires only the connection of the PWM signal and to a contact select the direction of motor rotation DIR. Flags FF1 and FF2 indicate incorrect operation of the system. Pin RESET to default selected to supply. When the status is restored low, the system will go into a state of minimal energy consumption. Will reset all flags.

 


         

Set includes

  • Driver module
  • Electrolytic capacitor
  • The bar goldpin
  • Connectors ARK

 

Insights

 

 

PINDescription
V+Motor power supply (5.5 V-30V). The conclusion is denoted by the symbol + is the positive pole connections of the capacitor. Less output V+ allows you to control the power of the engine. Not recommended for high currents.
5V (out)The output of the voltage regulator is 5V. The output current to a few mA. Be careful to avoid a short circuit with the adjacent terminal V+ as it leads to irreversible damage of the module.
GNDThe potential of mass of the system.

OUT

OUTB

Insights for the DC motor.
PWMSignal speed control. Default in the low state
DIRThe choice of the direction of rotation of the motor. In the high state, the current flows from the output OUT to OUTB. By default, the floating state (float).
RESETAfter filing lowest position the system is in a low power state. Removes all the flags.

FF1.

FF2

Status flags system. In the event of an error, the status is high.

 

 

Status flags system

The state of FF1 and FF2 insights inform the user about the current status of the system HighPower. The description of individual sequences presented in the table below.

 

FF1.FF2DescriptionBlocked
output
LLNo errorsNOT
LHShort circuitSO
HLTemperature too highNOT

H

H

Voltage too lowSO

 

  • Voltage to 5.5 V
  • Voltage from 30.0 V
  • Current 15 A
  • Channels 1

SAME DAY SHIPPING

Posting the payment for the order on our account on a business day up to 13:00 means sending the goods on the same day!

 

The time of payment depends on the hours of ELIXIR session of the sender's bank and the recipient of the transfer (more information on this subject, for example on the websitehttp://www.kiedy-przelew.pl/).

 

The table presents available forms of delivery in Poland

 

Carrier and
regulations

Bank wire
transfer

Payment
by cash

Delivery
time

Poczta Polska

terms of service

9,90 PLN17,90 PLN1-3 days

Kurier GLS

terms of service

14,90 PLN22,90 PLN

1-2 days

Paczkomaty 24/7 

terms of service

12,90 PLN-1-3 days

If the amount to pay for products exceeds 500 PLN
Delivery is for free!

 

  • Free delivery of orders over 500 PLN does not apply to parcels addressed outside of Poland.
  • Free delivery does not apply when changing orders.
  • The delivery period is counted in working days from the date of dispatch of the order.