DRV8838 - single-channel motor controller 11V/1,7A - Pololu 2990

Index: PLL-02695 EAN: 5903351244855

Single-channel DC motor controller. Continuous current per channel 1.7 A (momentary to 1.8 A). Supply voltage up to 11 V.

DRV8838 - single-channel motor controller 11V/1,7A - Pololu 2990
€5.00
€4.07 tax excl.
Available
Shipping in 24 hours
PayPal payment
Manufacturer: Pololu
Compatibility: Arduino Raspberry Pi

Description: PololuDRV8838 - single channel motor controller 11V/1.7A

The module based on theDRV8838allows to control one DC motor. The motor can be supplied with a voltage of up to 11 volts with a continuous current consumption of up to 1.7 A, and temporarily (for a few seconds) up to 1.8 A. We recommend that you readthe DRV8838's documentationbefore use.

Connection

Podłączenie jednokanałowego sterownika silników Pololu

Connect the motor supply voltage from 0 to 11 V to the VIN input. If the voltage is low (less than 1.5 V) it can be connected to the VMM output, this will bypass the reverse connection protection and compensate for the voltage drop. The power supply for the logical part from 1.8 V to 7.0 V is supplied to the VCC pin.

In a typical application, simply connect two control lines: PHASE direction selection and PWM speed control to the ENABLE pin. Both lines are internally pulled to ground by a resistor approximately 100 kΩ.

The SLEEP output enables the system to switch to low power mode. By default, the pin is pulled up to VCC via 10 kΩ, which means that the circuit is switched on. To switch to the Sleep mode, the low state must be specified.

PHASE ENABLE SLEEP OUT1 OUT2 Mode of operation
0 PWM 1 PWM L forward speed PWM %
braking
1 PWM 1 L PWM Reverse speed PWM %
braking
X 0 1 L L

Stop,

outputs connected to ground

X X 0 Z Z free running
outputs disconnected

1 - high state, 0 - low state

Exits

Opis wyprowadzeń sterownika silników Pololu

PIN Description

VIN

Motor supply voltage from 0 V - 11 V with reverse connection protection.
GND The weight of the module.
VCC Supply voltage of the logical part from 1.8 V to 7 V.
VM Motor supply voltage from 0 V - 11 V without reverse connection protection.
OUT1 Outputs 1 to connect the motor outputs.
OUT2 Outputs 2 to connect the motor outputs.
PHASE Logical input defining the direction of engine rotation. Default is in low state.
ENABLE Logical input for speed setting. A PWM signal must be connected to this output. Default is at low state.
SLEEP Logical input that switches the system to the sleep state when low state is given. Default is high state.

Outputs are standardgoldpin strips, allowing the module to be plugged into thecontact boardor connected bywires.

Comparison of Polol controllers.

Polol specificationDRV8838

  • Number of channels: 1
  • Supply voltage: 0 V to 11 V
  • Operating voltage of the logical part: 1.8 V to 7.0 V
  • Continuous current per channel: 1.7 A
  • Maximum instantaneous current per channel: 1.8 A
  • PWM frequency: 250 kHz
  • Dimensions: 10.2 x 12.7 mm
  • Weight: 0.3 g (without connectors)
  • Included module and goldpin connectors

Voltage to 1.8 V
Voltage from 1.5 V
Current 1.7 A
Channels 1
Package width 7.5 cm
Package height 0.5 cm
Package depth 5 cm
Package weight 0.002 kg

Be the first to ask a question about this product!

Product reviews

DRV8838 - single-channel motor controller 11V/1,7A - Pololu 2990

5/5

Average grade

2

Customers opinion
The following opinions are collected
and verified by
an external partner Trustmate
and come from the post-purchase process.

Zdjęcia użytkowników

Customers who bought this product also bought:

Products from the same category: