Categories

Pololu ACS711EX current sensor ACS711EX -15A to + 15A*

Current sensor working in the range of +/-15 A based on the Hall effect. The output is an analog voltage. Supply voltage is from 3.0 V to 5.5 V.

More details

PLL-01690

Pololu

Dodano produkt do koszyka

In stock, shipping 24 hours!

Price 13,90 zł

Specification

  • Supply voltage of the logic part: 3.0 V to 5.5 V
  • Measuring range: from 15 A to 15 A
  • Current consumption of the logic part: 4 mA
  • Sensitivity for power supply of 3.3 V: 0,090 V/A
  • Bandwidth: 100 kHz
  • Operating temperature: -40 °C to 125 °C
  • Module weight: 1 g (without connectors)
  • Dimensions: 18 x 20.5 mm

 

Description

The module consists of a printed circuit board made for the system Allegro ACS711KEXLT-15AB-T. The sensor operates based on the Hall effect. The chip can be powered from a voltage in the range: 3 V to 5.5 V.

 

Main features of the module:

  • The system is designed for current flowing in both directions (from -15A to 15A)
  • The module withstands the current surges of up to 100 A for 100 MS
  • Due to the low resistance of the system (0.6 mΩ) and channeling, the power losses are very small.
  • Through the use of Hall effect, the current paths are isolated from the logic part.
  • The bandwidth is 100 kHz
  • The FAULT pin which informs about exceeding the range of 15 A
  • Operating temperature: -40 °C to 125 °C
    

 

Connection method

The sensor requires a supply voltage in the range from 3 V to 5.5 V, connected to the pins designated as VCC (+) and GND (ground). The output is a voltage signal proportional to the intensity of the measured current. When the voltage VCC is equal to 3.3 V, the output is centered on the half, that is 1.65 V. The output value increases by 90 mV at 1 A when the strength of the measured current is positive, otherwise, it decreases.

 

Formulae allowing to calculate the output values:

 

The FAULT pin is by default in the high status. It reaches a low status when the value of the measured current exceeds the range of ±15 A. The only way to reset the Fault flag, is to disable and then re-connect the - VCC power supply.

 

 

Attention!

The system is designed to work with voltages below 30 V. Higher values can pernamently damage the module.

 

 

Scheme

The module includes the passive components which are necessary for proper operation of the ACS711 sensor.

SAME DAY SHIPPING

Posting the payment for the order on our account on a business day up to 13:00 means sending the goods on the same day!

 

The time of payment depends on the hours of ELIXIR session of the sender's bank and the recipient of the transfer (more information on this subject, for example on the websitehttp://www.kiedy-przelew.pl/).

 

The table presents available forms of delivery in Poland

 

Carrier and
regulations

Bank wire
transfer

Payment
by cash

Delivery
time

Poczta Polska

terms of service

9,90 PLN17,90 PLN1-3 days

Kurier GLS

terms of service

14,90 PLN22,90 PLN

1-2 days

Paczkomaty 24/7 

terms of service

12,90 PLN-1-3 days

If the amount to pay for products exceeds 500 PLN
Delivery is for free!

 

  • Free delivery of orders over 500 PLN does not apply to parcels addressed outside of Poland.
  • Free delivery does not apply when changing orders.
  • The delivery period is counted in working days from the date of dispatch of the order.