Shunt Regulator: 26,4V, 4,0Ω, 9W - Pololu 3774

Index: PLL-13475 EAN: 5904422341770

The shunt regulator can protect the power supplies from voltage spikes generated by the motor controllers connected to them. This version has a fixed value of 26.4 V, a shunt resistance of 4.0 Ω and 12 SMT shunt resistors located on one side of the PCB. An external potentiometer can be used to set the voltage.

Shunt Regulator: 26,4V, 4,0Ω, 9W - Pololu 3774
€10.90
€8.86 tax excl.
Waiting time: 4-6 weeks
Only on request
PayPal payment
26.4V shunt voltage regulator - power:
Manufacturer: Pololu

Product description: By-pass voltage regulator 26.4 V, 4.0 Ω, 9 W - Pololu 3774

The shunt regulator canprotectpower suppliesfrom voltage spikes generated bymotor controllersconnected to them. This version has a fixed value of26.4 V, a shunt resistance of4.0 Ωand12 SMT shunt resistorslocated on one side of the PCB. An externalpotentiometercan be used toset the voltage.

The regulator should be installed in parallel with thepower supplyfor proper operation. The supply voltage should be lower than the regulator voltage and the regulator should draw only resting current less than 0.5 mA. Any voltage pulses above the setting will cause the regulator to draw significantly more current, dissipating energy and limiting the range of voltage variation.

Bocznikowy regulator napięcia 26,4V, 4,0Ω, 9W - Pololu 3774

Shunt voltage regulator 26.4 V, 4.0 Ω, 9 W - Pololu 3774.

Wiring diagram of a shunt regulator between the power supply and the motor controller.

Shunt regulator diagram

Below is a simplified schematic of a shunt regulator. The circuit monitors the voltage and controls theMOSFET, which allows current to flow through the shunt resistance, which sets the maximum current the device can absorb.

Simplified schematic of a shunt regulator.

All Pololu shunt regulators differ only in voltage value and resistance. The available versions can be found in the table below:

Voltage
13,2 V 26,4 V 33,0 V Fine adjustment LV Fine adjustment of HV
Power: 3 W
-
-
32,8 Ω
-
-
9 W
1,33 Ω
4,00 Ω
4,00 Ω
-
-
15 W
1,50 Ω
2,80 Ω
4,10 Ω
1,50 Ω
4,10 Ω

On the left is the lower appearance of the 3 W and 9 W regulator, while on the right is the 13 V, 1.50Ω, 15 Wregulator.

Note!

The power is primarily intended to indicate the relative average power consumption for a maximum of a few seconds. The boards are designed to clip occasional, short pulses. Prolonged application of voltage above the set point will destroy the regulator almost immediately (in less than a second).

Adjusting the voltage set point

The shunt regulator is available in two adjustable versions with multi-turn potentiometers. All fixed voltage versions can also be adjusted by adding a potentiometer on the board.

The two adjustable versions differ only in the shunt resistance and the mapping optimization of the voltage setting potentiometer.

On the left are the leads for the fixed-voltage regulator, on the right are the leads for the adjustable-voltage regulator.

Schematics of the set voltage relative to the adjusted potentiometer:

Left side LV curve: 1.50Ω, 15 W. Right side HV curve: 4.10 Ω, 15 W.

Diagrams of the adjusted voltage versus adjusted potentiometer

The HV curve was obtained using a 200 kΩ potentiometerwith a 33.0 V plate, using a 200 kΩ potentiometer with low voltage fixed value plates will disturb the mapping by looking like an LV curve. (100 kΩ or lower value potentiometers can be used at the expense of higher resting current, since the full supply voltage is applied through this potentiometer.)

When setting the voltage with a potentiometer, or to check the exact voltage of any shunt regulator, connect a higher voltage with a current-limiting resistor of at least a few hundred Ω and measure the voltage on the regulator. (Without a current limiting resistor, the regulator would not work if it was set higher than the test supply voltage and would start to smoke if it was set below your supply voltage !) Typically, you should set the regulator about 10% above the supply voltage.

Specifications of shunt voltage regulator - Pololu 3774

  • Output voltage: 26,4 V
  • Shunt resistance: 4.0Ω
  • Power: 9 W
  • Maximum resting current: 0.5 mA
  • Dimensions: 28.5 x 20.3 x 7.6 mm
  • Weight: 2.8 g

Length 29 mm
Width 21 mm
Height 8 mm
Voltage to 26.4 V
Voltage from 26.4 V
Voltage output from 26.4 V
Output voltage to 26.4 V
Current 0.3 A
Stabilizer - Type2 shunt

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: