Categories

Step-Up Voltage Regulator U3V70F6 - 6V 10A - Pololu 2892

A type Converter step-up output voltage of 6 V. the Maximum current up to 10 A. supply Voltage range from 2.9 V to 6 V.

More details

PLL-14004

Pololu

Add to cart

This product is no longer in stock


Notify me when available

Price 52,00 zł

Product description: Converter step-up U3V70F6 - adjustable - 6 V 10 A

The regulator increases the voltage from the range from 2.9 to 6 Volts to a constant value of 6 Volts. The system is able to handle the input current with a maximum value of 10 Atypical input current makes 8 And for a few seconds, and then turn on the mode of thermal protection. It is recommended to use current up to 6 A, the inverter can run for many minutes. The output current is a function of the input voltage, output voltage and efficiency of the Converter. Details can be found in the graphs in the remaining part of the description.

Family U3V70x offers one version of the Converter with adjustable output voltage: U3V70A (4.5 to 20 V). Also available are versions with constant voltage: 5, 6, 7,5 V, 9 V, 12 V and 15 Volts. All versions of layouts U3V70x similar to each other, for easy identification on the reverse side is a blank space where you can put your own labels using the marker.

 

Connection of Converter U3V70F6

The module has four output:

  • VIN - the input voltage must not exceed the value of the output voltage.
  • GND - the ground.
  • VOUT - output voltage. In the case of an adjustable version is selected with the potentiometer.
  • ENABLE - switches the system to low power mode. Pin default pulled up to the supply voltage VIN through a resistor of 100 ohms. This means that while leaving the conclusion, which is not connected, the inverter is enabled by default. For the introduction of the system in protection mode, you must specify the status of the low (less than 0.4). In this case, the module consumes only the current flowing through resistor 100 kω this value of 10 µa depending on the attached input voltage.

  

Pololu U3V70F6

 

Connectors respectively signed on the Board. Terminal pitch 5 mm for joints of SHEETS and 2.54 mm connectors goldpin, which allow for the mounting of the module on the Board contact or connect with wires.

Pololu U3V70F6

  

The kit includes connectors for self-soldering. You can choose popular goldpiny or terminals high current ARK. Through the use of a thicker layer of the PCB plate lugs connectors do not protrude outside of the layout.

Output current and efficiency of the system step-up U3V70F6

The efficiency of the Converter depends on input voltage and output voltage. On average, from 80% to 95 %. The output current is a function of the input voltage, output voltage and efficiency of the Converter. Typically, this value is in the center of the input current.

 

Fig. 1: the efficiency of the system with output voltage of 6V.

Summing up, the maximum output current proportional to input voltage and output voltage. In addition, its value can change depending on external factors, e.g. temperature or air flow or the radiator.

Specification Converter step-up U3V70F6

  • Input voltage range of 2.9 V to 6 V
  • Output voltage: 6 Volts with an accuracy of 4 %
  • Maximum input current:
    • 10 A - temporary
    • 8 And - for a few seconds
    • 7 A - for a long time
  • Output current: see chart
  • Low current consumption at rest
  • An efficiency level of 80 - 95 %
  • Security:
    • Before reverse power connection
    • Heat is to turn the system off when too high temperature
    • On lock at too low supply voltage is below 2.5 V
    • Short circuit
    • Limit input current to 10 A
  • Two mounting holes for screws M2
  • Dimensions: 40,6 x 15,2 x 4.6 mm
  • Weight (without connectors): 3.4 g

  • Length 41 mm
  • Width 15 mm
  • Height 5 mm
  • Voltage to 2.9 V
  • Voltage from 6.0 V
  • Voltage output from 6.0 V
  • Output voltage to 6.0 V
  • Nominal output voltage 6.0 V
  • Current 3.5 V
  • Stabilizer - Type2 switching
  • Stabilizer - Type step-up

SAME DAY SHIPPING

Posting the payment for the order on our account on a business day up to 13:00 means sending the goods on the same day!

 

The time of payment depends on the hours of ELIXIR session of the sender's bank and the recipient of the transfer (more information on this subject, for example on the websitehttp://www.kiedy-przelew.pl/).

 

The table presents available forms of delivery in Poland

 

Carrier and
regulations

Bank wire
transfer

Payment
by cash

Delivery
time

Poczta Polska

terms of service

9,90 PLN17,90 PLN1-3 days

Kurier GLS

terms of service

14,90 PLN22,90 PLN

1-2 days

Paczkomaty 24/7 

terms of service

12,90 PLN-1-3 days

If the amount to pay for products exceeds 500 PLN
Delivery is for free!

 

  • Free delivery of orders over 500 PLN does not apply to parcels addressed outside of Poland.
  • Free delivery does not apply when changing orders.
  • The delivery period is counted in working days from the date of dispatch of the order.