Step-Down Voltage Regulator D24V150F7 - 7.5V, 15A - Pololu 2883

Index: PLL-07615 EAN: 5904422360108

A step-down converter with an output voltage of 7.5 V. The maximum current is 15 A. The supply voltage is within a wide range from 9 V to 40 V. Dimensions of the module are 43 x 32 mm.

Step-Down Voltage Regulator D24V150F7 - 7.5V, 15A - Pololu 2883
€124.50
€101.22 tax excl.
Waiting time: 4-6 weeks
Only on request
PayPal payment
D24V150F inverter - voltage:
Manufacturer: Pololu

Specification of the D24V150F7 converter

  • Input voltage: from 9 V to 40 V
  • Output voltage: 7,5 V
  • Output voltage accuracy: 4 %
  • Continuous output current: 15 A
  • Efficiency: 80% to 95%
  • Integrated protection against overcurrent, overvoltage and overtemperature
  • Four mounting holes with 2,2 mm diameter
  • Dimensions: 43 x 32 x 11 mm
  • Weight (without connectors): 19 g

Product description: D24V150F7 - 7,5V 15A step-down converter - Pololu 2883

Step-down (buck) converter used to power systems operating at 7.5V. The advantage of the circuit is a wide range of input voltages from 9 V to as much as 40 V.

The D24V150F7 module allows up to 15A current consumption. In our offer there are also available step-down circuits from the series D24VxFy with different maximum voltages and currents.

Leads of the converter

Pin Description
VIN Input voltage from 9 V to 40 V.
GND Ground potential.
VOUT Output voltage.
ENABLE . Applying a low voltage state below 1 V) causes the circuit to go into a low power state (about 10 μA). The pin is pulled up to the supply voltage through a 100 kΩ resistor, making the circuit on by default.
PG Energy Meter. An open-drain output that goes low when the voltage drops below 85% of nominal or rises above 115%. Use an external pull-up resistor to use this pin.
MOD Mode pin, internally pulled low, which selects the fixed frequency mode. Pulling up to high reduces the resting current (while increasing efficiency) at low loads (on the order of a few milliamps). Function available when the input voltage is much higher than the output voltage.

The connectors are properly signed on the board. Pinout is 2.54 mm (goldpin). The module can be plugged into a contact board, connected with wires or soldered into a dedicated PCB.

System efficiency

Efficiency is defined as the ratio of output power to the input power (Power out)/(Power in). It is a very important parameter in the case of work with portable sources of energy (batteries and accumulators), where the time of work on one charging cycle counts. The efficiency of this pulse circuit is about 80 % - 95 %.

Drop-out voltage

This parameter is defined in the documentation as drop-out voltage is necessary for the proper functioning of the system, minimum difference between input and output voltage. For example, if the drop-out is 1 V and the desired output voltage is 5 V, the value of the supply voltage should be higher than 6 V. The figures below show the drop-out voltage value for D24VxFx converters.

Length 43 mm
Width 32 mm
Height 11 mm
Voltage to 9.0 V
Voltage from 40.0 V
Voltage output from 7.5 V
Output voltage to 7.5 V
Nominal output voltage 7.5 V
Current 15 A
Stabilizer - Type2 switching
Stabilizer - Type step-down
Package width 8 cm
Package height 0.9 cm
Package depth 11.5 cm
Package weight 0.005 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: