• EOL

Arduino Uno Rev3 with long pins - module A000099

Index: ARD-10049 EAN: 8058333491769

Popular module with microcontroller AVR ATmega328 in a replacable case. Has 32 KB of Flash memory, 2 KB RAM 14 digital I/o, 6 of which can be used as PWM channels, 6 analog inputs and popular communication interfaces. Version with long pins.

Arduino Uno Rev3 with long pins - module A000099
€25.50
€20.73 tax excl.
Unavailable
Discontinued product
PayPal payment
Manufacturer: Arduino

Attention!

The product has been discontinued. Check others products incategory.

Description

Arduino Uno is the primary and, at the same time, the most popular version of the entire series. The board containsan ATmega328 microcontroller equipped with 14 digital I/o, 6 of which can be used as PWM outputs (e.g. for motor control) and 6 analog inputs. The system works with the signal ticking with the frequency of 16 MHz and has 32 KB Flash memory and 2 KB RAM SRAM.

This version of Arduino Uno has a long male pins on the bottom side of the tile. In our offer is also availablethe traditional version of this module.

Arduino uno rev3 - moduł, platforma, atmega328, płytka,

The object of the sale is an original product for Arduino, Botland isthe official distributor of this company.

Key features

Below are a few features that distinguish modules Arduino from the other programmable tiles.

 

NameDescription

Installed

bootloader

Thanks to bootloader, for programming the device, the only necessities are appropriateUSB cableandsoftware from manufacturer's website.

Arduino

Shield

The distribution of connectors allows the installation of special plates, so-calledArduino Shield.

Digital I/O

14 digital inputs/outputs allow, in particular, controlling the LEDs, relays and reading the buttons' states.

Efficiency

current

The maximum power load for a single output is 40 mA.

Output

PWM

6 PWM outputs allow to control the motors brightness of the LEDs.

Analog inputs

6 inputs of built-in digital-analog converter with a resolution of 10-bit, support, in particular, sensors with analog output.

Serial communication

The device supports popular communication interfaces, including UART, I2C and SPI.
Special functions Some of the pins have special functions that a brief description is available inour guide.

Built-in memory

Atmega328 system with a clock signal with a frequency of 16 MHz, has 32K Flash memory, 1 KB EEPROM and 2 KB of RAM SRAM.

Power

DC connector

To power the Arduino, you can useany power sourcewith a voltage from 7 V to 12 V with DC connector 5.5 x 2.1 mm.

Power

USB port

The tile can be powered from a computer via USB cable, bearing in mind that the maximum load current for the USB port is 500 mA. Arduino has a system that protects the socket from short-circuit and the flow of too high current.

Connector

ICSP

The module has ICSP I/O for connecting an externalAVR programmer.

Pin

IOREF

The IOREF pin provides direct access to the voltage with which output I/O work.

Built-in

led

The connected led on pin 13 allows debugging simple programs.

Output

3.3 V

Built-in voltage regulator provides power to external devices with the voltage of 3.3 V with current consumption of 50 mA.

Microcontroller

in THT

Through the use of through-hole case THT, in case of damage tothe main microcontroller Atmega328P, you can easily replace it.

 

First run

To help you get started with the module, we have prepareda tutorial that will help you with the installation and first run of the Arduino environment.

 

Arduino uno rev3 - moduł, platforma, atmega328, płytka,

The distribution of elements on the Arduino Uno.

 

Specification

  • Supply voltage from 7 V to 12 V
  • Microcontroller: ATmega328
    • Maximum clock frequency: 16 MHz
    • SRAM: 2 KB
    • Flash memory: 32 KB (5 KB is reserved for bootloader)
    • EEPROM: 1 KB
  • I/O Ports: 14
  • PWM outputs: 6
  • Number of analog inputs: 6 (channels of converter A/C with 10 bit resolution)
  • Serial interfaces: UART, SPI, I2C
  • External interruptions
  • The connected led on pin 13
  • USB A connector for programming
  • DC connector 5.5 x 2.1 mm for power
  • Version equipped with long pins

ThingSpeak platform for Arduino and Raspberry Pi IoT.

 

We guarantee that all tiles marked with a symbol Arduino are genuine and come from the same source. As you can see by checkingthe list of authorized distributors.

Voltage to 7.0 V
Voltage from 12.0 V
Voltage output from 5.0 V
Output voltage to 5.0 V
Nominal output voltage 5.0 V
UC - Microcontroller ATmega328
UC - Core 8-bit AVR
UC - EEPROM 1 kB
UC - Flash 32 kB
UC - RAM 2 kB
UC - core 1. Single Core
UC - Digital pins 14
UC - analog in 6
UC - freq 16 MHz
UC - A/C 10-bit
UC - PWM 6
UC - USB USB B
UC - I2C yes
UC - UART yes
UC - SPI interface yes
Package width 0.001 cm
Package height 0.001 cm
Package depth 0.001 cm
Package weight 0.001 kg

Be the first to ask a question about this product!

Customers who bought this product also bought:

Products from the same category: