Lining, contains the communication modules, GPS, GSM, Bluetooth, wifi, XBee and a lot innnych.
Shield for Raspberry Pi which consists to the tuner of the terrestrial television. It enables the reception of all available, uncoded channels of digital terrestrial television in DVB-T and DVB-T2. It can also stream the signal over the network, to other devices.
Shield for Raspberry Pi, version Zero and Zero W adding full-size USB type A connector. It connects through the pinss of the pogo type. It is used for various systems, for example, Respoder, PoisonTap or using the platform P4wnP1.
Shield for Raspberry Pi, version 3 and 2, with the system allowing for communication via the RS232 interface. The module has a ST3232 converter which communicates via UART and is powered from the Raspberry Pi connectors. On the board are DB9 connector, as well as a place to create prototype systems.
USB extension for cameras ArduCAM is a versatile board, created to facilitate work with minicomputers such as Raspberry Pi and TI Beaglebone and the like or connecting the webcam to the computer. Supports most cameras from 0.3 MPx to 14 MPx with parallel interface.
Module with a camera intended for studying the application development using artificial intelligence. It is able to recognize faces, objects, symbols, etc. in real time. It works with most popular platforms including Raspberry Pi.
Shield for Raspberry Pi provides support of the system NFC of 13.56 MHz. Board works based on the NXP PN512 chip, it communicates via I2C or SPI interface. It can operate in three modes of NFC - reader, P2P, card emulation. The kit also includes a Mifare RFID card.
Cap adjusted to the GPIO connectors for Raspberry Pi 3 / 2 / Zero / Zero, which provides connection through standard GSM, GPRS, GPS and Bluetooth. Allows voice chat, to send sms messages. On the Board are: connector for SIM card, microUSB slot, 3.5 mm jack connector, place for battery and antenna connector u.FL.
Shield Pi-top Pulse for the Raspberry Pi is one of the additional accessories for laptop Pi-top. It has the LED matrix of 7 x 7 and a built-in microphone and speaker. Thanks to it, you can create your own games, music or make a light show. It works with Amazon Alexa so it can answer the questions.
Shield for Raspberry Pi, version A+/ B+ / 2 / 3 / 3+ / Zero / Zero W with system MAX3232 which allows for communication via the RS232 interface. The module has a converter which communicates via UART, and is powered from the Raspberry Pi connectors. On the board is also DB9 connector, as well as a place to create prototype systems.
Shield for Raspberry Pi that allows you to send text messages and create calls in the GSM network. It also has a GPS and LTE module. It communicates via serial interface UART (RX, TX) using the AT commands.
The module for self-assembly allowing the expansion of Raspberry Pi with additional analog connector VGA video. This allows for the connecting of two monitors simultaneously to HDMI and VGA. The module is compatible with the Raspberry Pi 3 / 2 / B+.
Do you want to know where your Raspberry Pi is at any time of the day or night? This shield allows you to read the actual time and position with a frequency of 10 Hz using a GPS and RTC system. The connectors are suitable for Raspberry Pi, version A+, B+ and 2 B.
Wi-fi module from Atmel operating in 802.11 bgn standard. The device works with voltage from 3.3 V to 5.5 V it communicates via interface SPI. It has support for SSL, WEP, WPA, WPA2 and AP mode which allows you to create ad-hoc network. The module also works with TLS 1.2 safety with firmware 19.4.4. On the board is a connector u.FL for connecting external...
A GPS MTK3339 module on the board with the goldpin connectors (strip in the kit for self-assembly). The installed system can track 22 satellites and is working with voltage from 3.0 V to 5.5 V, has Flash memory, the update frequency is 10 Hz.
The module supports GSM and GPRS communication. It allows for voice calls, sending SMS messages. On the board are: two connectors for SIM card, powering module for battery LiPol, as well as POWER and RESET buttons. Version works with Arduino and Raspberry Pi, it has a connector for antenna u.FL.
Shield for Raspberry Pi, version 3B+ / 3B / 2B / Zero / Zero W with system SN65HVD230 which allows communication between CAN and SPI and the SP3485 system that enables communication between the UART and RS485. It is powered from connectors of the Raspberry Pi.
Cloudio is a shield for the RaspberryPi with the possibility of programming with a smartphone using a special app. Board has a voice assistant functions, integration with IFTTT, supports cloud IoT and also allows you to monitor the sensors.
Shield for Raspberry Pi, version A+ / B+ / 2 / 3 / 3+ / Zero / Zero W with system MAX3232 which allows for communication via the RS232 interface. The module has a converter which communicates via UART, it is powered from the Raspberry Pi connectors. On the board is DB9 connector, as well as a place to create prototype systems.
This project shows how to start the recognition of a natural language and how to link it with Google Assistant using a voice set AIY Projects. To everything that Google Assistant do, you can add your own questions and answers. All is closed in a small, cardboard cube powered by Raspberry Pi.
Shield for Raspberry Pi, version A+ B+ / 2 / 3 / 3+ / Zero / Zero W with system SN65HVD72 allowing communication between the 3.3 V UART and RS-485. It is powered with connectors of the Raspberry Pi. On the board is also DB9 connector.
The new version of the module working with Arduino and Raspberry Pi that provides communication in GSM and GPRS. Based on Quectel M95, it allows for voice calls, sending SMS messages. On the board are: two connectors for SIM card (dual SIM), microSD slot and outputs/inputs of the audio. There are no connectors for the Arduino.
The module supports GSM and GPRS communication. It allows for voice chat, sending SMS messages. It also has a built-in Bluetooth 3.0 for wireless communication. On the board are: slot for SIM-cards, powering module for a LiPol battery and the POWER button. The version works with Arduino and Raspberry Pi, it has a Jack for antenna u.FL.