Arduino is an already well-known platform of programmable embedded systems. From year to year, the hardware and software (Arduino IDE) of the Italian manufacturer is increasingly appreciated. A simple interface and integrated programming environment favor the creation of many interesting and practical projects. In addition to standard hardware and software equipment, you can also attach dedicated modules that significantly expand the standard capabilities of Arduino! Among many different overlays (Arduino Shields) you can find special devices that are responsible for communication. Thanks to them it will be possible to connect one device to another. In order to do this, you can use a Bluetooth connection, Wi-Fi or radio communication. Communication modules for Arduino surprise with their universality. They are used for both home and smaller projects, as well as for the largest projects implemented by laboratories or enterprises. Arduino guarantee also a lot of fun for every enthusiast of programmable electronics! Check out our offer of several dozen communication modules that are compatible with Arduino! Choose the Arduino Shield overlay that will be tailored to your needs!
Shield for Arduino with RTC DS1307 and a slot for SD memory cards. It can be used as a data logger, it has a place for a round CR1220 battery and for additional module. It works with the Arduino Uno and derivatives
The module working with Arduino and Raspberry Pi that provides communication in GSM and GPRS standard. It allows for voice chat, sending SMS messages. On the board are: two connector for SIM cards (dual SIM), microSD slot and outputs/inputs of the audio.
Shield for Arduino with connectors of the controller of the PS2 console. It communicates through UART interface. It supports wired and wireless controllers. The board has jumpers that are used to select baudrate of the UART interface and select the RX and TX pins, as well as buttons and status LEDs.
Shield for Arduino with RTC DS1307 and a slot for SD memory cards. It can be used as a data logger, it has a place for a round CR1220 battery and for additional modules. It works with the Arduino Uno and derivatives.
The module supports communication in GSM 900 MHz / 1800 MHz and UMTS 900 MHz / 2100 MHz. It allows for voice calls, sending SMS messages. On the board are: connector of SIM card, powering module for battery LiPol, as well as POWER and RESET buttons. Version works with Arduino and Raspberry Pi, it has a connector for antenna SMA.
The module supports GSM and GPRS communication. It allows for voice calls, sending SMS messages. On the board are: two connectors for SIM card, powering module for battery LiPol, as well as POWER and RESET buttons. Version works with Arduino and Raspberry Pi, it has a connector for antenna SMA.
The module supports communication in GSM 900 MHz / 1800 MHz and UMTS 900 MHz / 2100 MHz. It allows for voice calls, sending SMS messages. On the board are: connector of SIM card, powering module for battery LiPol, as well as POWER and RESET buttons. Version works with Arduino and Raspberry Pi, it has a connector for antenna u.FL.
The module is working with Arduino, which provides connectivity in GSM and GPRS. It allows for voice calls, sending SMS messages. It also has a GPS module. On the Board are: connectors for SIM card, output Jack, battery charger lipol and connectors u.FL for external antenna.
Shield for Arduino MKR, which allows you to connect microSD card. It also has a Flash memory of 2 MB and space for prototyping. It has a built-in Winboard W25Q16 chip. It communicates via the SPI interface. It works with a voltage of 3.3 V.
The module supports GSM and GPRS communication. It allows for voice calls, sending SMS messages. On the board are: two connectors for SIM card, powering module for battery LiPol, as well as POWER and RESET buttons. Version works with Arduino and Raspberry Pi, it has a connector for antenna U.FL.
Shield for Arduino, which extends the abillities of pins of the I/O. It has, i.a. a slot for XBee modules and service of modules of SD cards, APC220 radio modules, Bluetooth, Xbee communication, servo and RS485.
Lora IoT Node Shield is a special panel module with a microcontroller like Arduino. The module provides node creation Laura, compatible with The Things Network in combination with the Arduino. Trim system is used RAKWireless RAK811 Laura, who opraty technology SemTech SX1276 Lora. Board uses a frequency of 868 / 915MHz.
Module from the Gravity series enables the processing of the current signal from 0 mA to 25 mA into a voltage signal from 0 V to 3V. The sensor may be connected to the Gravity expansion module of pins V7.1. It is supplied with the voltage from 3.3 V to 5 V.
The new version of the module working with Arduino and Raspberry Pi that provides communication in GSM and GPRS. Based on Quectel M95, it allows for voice calls, sending SMS messages. On the board are: two connectors for SIM card (dual SIM), microSD slot and outputs/inputs of the audio.
Shield for the Arduino that allows you to save data to the SD card. RTC built-in clock allows to save the exact time. The system communicates via I2C, works with plates Uno R3, Duemilanove, Diecimila, Leonardo and Mega 2560 R3 and ADK.
Board that facilitates the use of the LinkIt Smart 7688 Duo module via this module's function out on the Ethernet connectors, 3.5 mm Jack, USB and 4-pin Grove connectors. TThanks to it, the connection of sensors becomes much easier. The board supports the I2C bus and 2 x UART.
Panel module for Arduino expansion capabilities FPGA from Xilinx Spartan. The Board also has a system ESP32 that allows you to exchange data via wi-fi and Bluetooth and 8-bit ADC, a 6-axis accelerometer, two LEDs RGB interface miniHDMI, two connector camera CSI interface and the Grove.
Shield for Arduino, enabling the reading of data from the NFC devices and RFID at 13.56 MHz. The module has integrated antenna, it is supplied with the voltage from the Arduino pins, it communicates via I2C or SPI bus.
There are many types of products among the Arduino communication overlays. Some provide Internet communication, others via Bluetooth, and others use radio waves.
One of the more popular products are overlays such as Arduino Ethernet Shield, Arduino MKR Ethernet Shield, LinkIt Smart, Ethernet Shield W5100 for Arduino and many others.
An overlay such as the Arduino Ethernet Shield enables communication of Arduino boards with external devices via the internet. The second, latest version of the module is based on the W5500 chip and is equipped with a microSD card reader. To run the Ethernet Shield overlay, connect it to the GPIO pins on the Arduino board (e.g. Arduino Uno), and then connect to the computer via a USB cable.
With Arduino communication modules, your programming options will become almost limitless. Why? First of all, Arduino Communication Shields solve the problem of integrity. With these overlays you will connect the devices you created (e.g. a robot) with almost any other software. Go ahead and use these products if your products assume the creation of mobile applications and computer programs!
Arduino communication modules are relatively not expensive, but they give a lot of new options! You can upload ready-to-use programs to the board and disconnect from the computer. After loading the program, the board can work independently. Then just connect the external AC adapter.
Arduino communication modules will be connected to a computer or router using a standard CAT5 or CAT6 Ethernet cable with a classic, most popular RJ45 connector. For the communication board to connect properly, be sure to assign its MAC address and permanent IP address. The latter parameter is programmatically assigned via the Ethernet.begin () function, with IP addressing depending on the configuration of your network. By using DHCP, you can easily assign an IP address for the Arduino communication module. In addition, you'll be able to specify a network gateway or subnet (if there is any). Please note that Ethernet Shields also work perfectly with a library that supports microSD memory cards.
We know perfectly how good it is to have a wide choice. That is why in Botland store you will find modules that are responsible for GSM communication.
Using the Arduino GSM Shield 2 module, you can connect the Arduino to the internet as well as send and receive voice phone calls and SMS messages. The overlay has a built-in Quectel M10 radio modem. AT commands can also be used to communicate with the board. Pin No. 2 on the GSM Shield 2 board is connected to the TX pin of the M10 modem and pin 3, respectively, with the RX pin.
The M10 modem can operate on GSM 850 MHz and 900 MHz, DCS 1800 MHz and PCS 1900 MHz frequencies and supports TCP / UDP and HTTP communication protocols through GPRS connectivity with a maximum data rate of 85.6 kb / s. In order for the Arduino GSM Shield 2 to work properly and work with mobile networks, you need to connect a SIM card to it. You can get it from any GSM network operator.
In some ways thanks to Arduino it will be possible ... to create your own mobile phone!