The module is a card reader and contactless RFID transponders operating in the standards: Unique, HITAG-1, HITAG-2, HITAG-S, Q5, HID. Operating frequency of 125 kHz. CTU-D4R has built-in relays, buzzer and antenna. The module allows you to configure the format of the transmitted ID number, and transfer security password.
The RFID card reader. Working with providers of Unique, Hitag-1, Hitag-2, Hitag-S, Q5, HID, operating on a frequency of 125 kHz. Has a memory card with a built-in unit bolts. CTU-D5R allows you to configure the format of the transmitted ID number, and protection of data transmission with a password. The module has a built-in antenna, relay, and buzzer.
The product is intended for monitoring of the readings obtained from other devices using MODBUS RTU. AGEDI-B enables cyclic reading of the temperature with two sensors from the family of the DS1920, connected to 1-Wire interface. The device has eight ports of I/0 that provide remote reading and changing their state. The product enclosure designed for...
Card reader RFID operating at a frequency of 13.56 MHz. MM-R5 bases its activities on the principle of non-contact recording and reading of a transponder, operating on the basis of the standard MIFARE. The device uses the communication interface with voltage levels compatible with TTL. Reader has a built-in boot loader (bootloader).
Wall-mounted card reader and contactless RFID transponders, operating at a frequency of 13.56 MHz. Compatible with standard MIFARE Classic, MIFARE Plus, MIFARE Ultralight C, MIFARE DESFire, ICODE SLI, iClass. The reader was equipped with three GPIO pins. The device has a built-in LED diode, RGB and touch the button. Carcass in grey color.
The reader of transponders and contactless RFID cards operating at 13.56 MHz. Compatible with MIFARE, MIFARE Plus, ICODE SLI, and iCLASS. CTU-R5RM supports the following communication interfaces: RS485, RS232, TTL, SPI, I2C, WIEGAND, 1-Wire. Has two outputs GPIO. Reader allows the cards and tags programming NFC in accordance with ISO/IEC14443.
Reader proximity card RFID operates at a frequency of 13.56 MHz. Miniature devices are compatible with transponders operating in the MIFARE standard. NANO-MS uses the RS232 interface (TTL) with the output control line RS485 with adresowalnością on the data bus in mode RS485, 1-Wire, I2C, SPI, WIEGAND. This version is designed for surface mounting SMD.
Desktop reader and the USB programmer for transponders and RFID contactless cards. The device supports MIFARE Classic, DESFire, DESFire EV1, Plus, Ultralight, Ultralight C. operating Frequency PAC PUB is 13.56 MHz. The reader can perform the timer function of tags and cards, NFC is compatible with ISO/IEC14443 Product in black.
The device performing the function of reader and USB programmer for transponders and RFID contactless cards. PAC-pug compatible with MIFARE Classic, DESFire, DESFire EV1, Plus, Ultralight, Ultralight C Operates at 13.56 MHz. It can also perform the function of the programmer card and NFC tags are compatible with ISO/IEC14443. The product in beige color.
Wall-mounted RFID readerworking with the standards HID ISOProx II, HITAG 1, HITAG 2, HITAG S, Q5, Unique (EM4102). The device operates on a frequency of 125 kHz. Are used for communication protocols and MODBUS Netronix. UW-D4G were equipped with RS485 interface. Reader has a built-in antenna, buzzer, relay and two led indicators.
The card reader and transponders RFID, adapted for wall mounting. Runs on a frequency of 125 kHz. This device is designed for contactless reading of data in accordance with the standard Unique (EM4102). UW-DAL is equipped with a built-in antenna, two signaling led, relay and buzzer.
Wall-mounted card reader and transponders RFID. Compliance with standards Unique, HITAG, Q5 and HID. Runs on a frequency of 125 kHz. UW-DNG uses the communication interface CAN 2.0 B for maintenance of access control system NACS. The reader is equipped with a buzzer, relays, two signal diodes and a built-in antenna.
Reader for transponders and contactless RFID cards are designed for wall mounting. Operates at a frequency of 13.56 MHz. Supports group standard MIFARE : Classic, Plus, Ultralight C, DESFire iCLASS (CSN only), ICODE SLI. UW-R4G has a RS485 interface with the Netronix transfer Protocol and MODBUS-RTU. The reader is equipped with a buzzer, relay, indicator...
The antenna used to make the installation of RFID access control. Runs on a frequency of 125 kHz. The resistance of the winding of the antenna is 14 ? with a tolerance of +/- 10%. The inductance has a value of 1 mH (+/- 5%).
Miniature proximity card reader RFIDoperates at a frequency of 125 kHz. Compatible with the following standards: Unique, Q5, HITAG 1, HITAG 2 (only reading ID), HITAG S, HID. The module uses the RS232 interface (TTL) with output control lines RS485, I2C SPI1-Wire, WIEGAND. Version of reader designed for surface mounting SMD.
The transducer signals transmitted via Ethernet to the signal interface serial port RS485. Change settings COTER-E4I is carried out via a network connection and TCP/IP control applications. The Converter has one Ethernet port and RS485. Was also equipped with LEDs indicating transmission via the serial interface, and the operation of the device.
The transition controller adapted to work together with access control system NACS (Netronix Access Control System). This solution is used.m.in to check of persons entering the building or room. The device has a memory, user groups, maps, and graphs. After correct configuration of the system, allows to work in mode offline and online.
The transducer signals transmitted via Ethernet to serial interface CAN 2.0 B. Allows you to simultaneously chat with even 112 devices connected to one bus. Converter provides the opportunity to expand the scope of CAN 2.0 B in frame Protocol NX-CAN, which provides compatibility with other devices access control from the company Netronix, in the framework...
Is adapted for mounting on the wall of reader of transponders and contactless RFID cards. Operates at a frequency of 13.56 MHz. UW-MDN is compatible with standard MIFARE (ISO14443-3). Uses interface 1-Wire (Dallas DS1990 emulation). The reader is equipped with a buzzer, two led signal and built-in antenna.