The sensors are multifunctional, in addition to performing tasks that we might require from the temperature sensor, allow us additional measurements of other factors such as pressure and humidity. This allows you to specify multiple values using only one device.
Humidity, temperature and pressure sensor powered with the voltage of 3.3 V with I2C and SPI interface. Measuring range: temperature: -40 °C to 85 °C, humidity: 10% RH to 100% RH, pressure: from 300 hPa to 1100 hPa.
Humidity, temperature and pressure sensor powered with the voltage of 3.3 V or 5 V with I2C and SPI interface. Measuring range: temperature: -40 °C to 85 °C, humidity: 0 %RH to 100 %RH, pressure: from 300 hPa to 1100 hPa.
Pressure sensor and temperature model BMP280, stamps Grove. Used to measure atmospheric pressure and ambient temperature. Compatible with the Arduino. It is small in size, consumes little power, is very easy to install and use.
Module for measurement of temperature and humidity via wi-fi network using the app on your smartphone from anywhere in the world. For use with Shelly, it is sufficient to configure the device via web browser. It works in temperatures ranging from -40°C to 60°C and humidity of 0% to 100%. It is powered with the CR123A 3 V battery. The module...
Humidity, temperature and pressure sensor powered with a voltage of 3 to 5 V with I2C and SPI interface. Measuring range: temperature: -40 °C to 85 °C, humidity: 10% RH to 80% RH, pressure: from 300 hPa to 1100 hPa.
Enviro pHAT is a wrapper for the Raspberry Pi with sensors BME280 and LTR-559 , allowing measurement of temperature, pressure, light levels and a proximity sensor. In addition, the pad has a colored display of 0.96" and a MEMS microphone. Pad is fully compatible with 40-pin GPIO connector on the circuit Board of the Raspberry Pi.
Complete module for measuring temperature and humidity via Wi-Fi network using a dedicated smartphone app from anywhere in the world. In order to use Shelly, you need to set up the device via web browser. It works in temperatures ranging from -40 °C to 60 °C and humidity of 0 % to 100% Powered by a CR123A battery 3 V.
The Grove module is equipped with a humidity, temperature and pressure sensor powered with the voltage of 3.3 V to 5 V with I2C and SPI interface. Measuring range: temperature: -40 °C to 85 °C, humidity: 0 %RH to 100 %RH, pressure: from 300 hPa to 1100 hPa. The kit also includes a cable suitable for Seeedstudio Base Shield v2.0.
Temperature and humidity sensor with a digital I2C interface. Measuring range: temperature is from -40 °C to + 123,8 °C, humidity is from 0% to 100 % RH. It has connectors for connecting the sensor via wires. It works with voltage from 2.4 to 5.5 V.
Siren wi-fi for use in confined areas. Has the powerful sound of 100 dB and a built-in sensor of temperature and humidity is Very easy to install, works without wires. Home has partnered with Google and Amazon's Alexa. Powered by two batteries CR123A, or through the micro usb connector is 5 V.
High precision temperature sensor and humidity SHT35. Measures temperature in range -40°C to 125°C with an accuracy of 0.1°C and humidity from 0% to 100% RH with an accuracy of 1.5% RH. Communicates through an I2C interface. Works with a voltage of 3.3 V and 5 V.
Digital sensor to measure atmospheric conditions i.e.: temperature from -40 °C to 85 °C, humidity from 0 to 100 % RH, pressure from 300 hPa to 1100 hPa, indirectly measuring the height up to 9.2 km and the detection of organic compounds and carbon dioxide in the air. The sensor communicates over the I2C bus, leads are working with...
Module with ultrasonic sensor URM09 and three measurement ranges to choose from 2 to 150 / 300 / 500 cm. It also allows for a temperature measurement. Supply voltage is from 3.3 V to 5.5 V. The measurement frequency can reach up to 50 Hz. It communicates using the I2C interface.
Tile development minikomputera BBC micro:bit, thanks to which kids will learn the major issues in the realm of nature. Has built-in different kinds of sensorsthat were marked with drawings on the tiles in the form of a tree. The module simulates a scenery consisting of a cottage between the tree and the top.
Si7021 sensor allows you to measure temperature in the range from -10°C to 85°C and a relative humidity range from 0% to 80% RH. Was equipped with a cord length of 50 cm, complete plug mini Jack, for connection with the device Sonoff TH16. The power supply voltage from 2.2 V to 3.6 V.
The module is equipped with a high-quality digital temperature sensor, humidity, gas & pressure. To the module power we use the voltage from 3.3 V to 5 Volt. Sensors of this type are an excellent basis for systems that control environmental parameters. Plate sensor is prepared for soldering of the connector.
Module with integrated temperature sensor and humidity with high accuracy. The sensor finds use in many applications and projects related to IoT and environmental monitoring. The module communicates with interface I2C, is supplied with the voltage of 3.3 V and 5 V. Conclusions the Board has a special field intended for soldering.
The module is equipped with sensors HDC2010, which is responsible for checking air quality in the city and CCS811 that measure temperature and humidity. The connection of these sensors into a single module greatly simplifies the implementation of the product in projects related to determining weather conditions, such as home weather station.
Module pressure sensor with a thermometer. Nutrition can be a voltage of 3.3 V or 5 V is. This type of sensor is very good to Express themselves in projects, weather stations and devices tested weathering. The module has connectors prepared for soldering.
Multisensor has six different sensors: motion (PIR), light, vibrations, temperature, humidity and UV, all enclosed in a compact case 46 x 46 x 40 mm. The Ssnsor operates using 2 CR123A batteries or microUSB cable 5V/0,5A. The sensor works with all popular systems, such as Z-Wave Domoticz, and so on.
Digital sensor to measure atmospheric conditions, i.e.: temperature from -40 °C to 85 °C, humidity from 0 to 100% Rh, and pressure from 300 hPa to 1100 hPa. The last value allows for indirect measurement of a height of up to 9.2 km. The sensor communicates over I2C or SPI bus, pins are working with the voltage of 3.3 V but the I2C...